How to Add 90 Degree Bend to 3" Lug Valve Fitting

Question

Question:

I am looking for a black water tank valve that is 3” FPT TO 3” 90 degree lug. Do you have that? THANKS

asked by: Barry H

0

Expert Reply:

The closest we have to what you're looking for is a combinations of parts:

- Valterra Waste Valve for RV Black Water Tank - 3" FPT to 3" Lug # T50B
- RhinoFLEX 90 Degree Elbow Fitting # CAM39485

Normally a 90 degree fitting is before of after the valve which is why we don't have any with this specific setup.

expert reply by: Jon G

0

Answer 1

The Valterra Waste Valve for RV Black Water Tank, #T50A has a 3" inner diameter measurement with a 3-1/2" measurement for the outside.

view full answer...

Answer 2

The depth of the Valterra Waste Valve for RV Black Water Tank part #T50A measures 4-1/4" end to end without the cap but please note the fittings don't butt up to the end on either side.

view full answer...

Answer 3

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 5

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 6

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 7

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 8

I do have an option but Glo-Brite is no longer in business so you won't be able to get any replacement parts for these lights such as lenses. The only option you have would be a full replacement for which the most similar option we offer is the…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 11

To wire two 6-volt batteries in series to produce 12-volts, you would connect the load to the positive terminal of battery #1. Connect the negative terminal of battery #1 to the positive terminal of battery #2. Ground the negative terminal of battery…

view full answer...

Answer 12

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

How to Add 90 Degree Bend to 3" Lug Valve Fitting

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching