Replacement 10" Hub-and-Rotor Assembly for 2012 ShoreLand'r Boat Trailer

Question

Question:

I have a 2012 shore lander boat trailer… went to replace bearings and saw that rotors are corroded… the attached picture has trailer specs and I have already purchased bearings and seals see attached pics. What replacement rotors do I need that will fit my trailer and the already purchased bearings and seals?

asked by: Richard S

0

Expert Reply:

Thank you for the information!

To replace your hub-and-rotor assembly I recommend using the Kodiak 10" Hub-and-Rotor Assembly # KHR10D which has the 5 on 4-1/2" bolt pattern you're needing as well as a Dacromet finish which is much more resistant to water corrosion than standard powder and zinc coatings.

expert reply by: Jon G

0

Seal for 3,500 lb Axle
(click to enlarge)

Bearings for 3,500 lb Axles
(click to enlarge)

Old Hub-and-Rotor Assembly for 3,500 lb Axle
(click to enlarge)

Answer 1

According to Shorlandr, your SLR22L trailer uses hubs with a L44649 inner and outer bearing. The #CE13511 hub you mentioned uses a different inner bearing, so it won't work for you. The good news is that the #CE13311 is the correct hub, assuming…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 4

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 5

You can convert surge brakes to an electric over hydraulic braking system. To do this, you will need an electric over hydraulic actuator and a brake controller. For an electric over hydraulic actuator, I recommend looking at the Carlisle HydraStar…

view full answer...

Answer 6

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 7

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 10

First you will need to remove the old hydraulic equipment. Remove the surge coupler or actuator, remove all the lines, and finally remove the brake assemblies. If you have 10 inch diameter hub and drums, you may need to replace those as well. If you…

view full answer...

Answer 11

Based on the information I could find on your 2023 Jayco Jayfeather 30QB travel trailer it appears you are going to have 4,400lb axles. You are going to need to verify the diameter of your current axles as some manufacturers like Lippert use a…

view full answer...

Answer 12

In order to verify the spindle dimensions so that you can pick out the correct hub/drum you have to get exact dimensions. For that you need to use a digital caliper like part #PTW80157. For how old your trailer is this is especially important as the…

view full answer...

Replacement 10" Hub-and-Rotor Assembly for 2012 ShoreLand'r Boat Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching