Replacement 30 inch Slipper Spring for PWC Trailer with 1,550 GVWR

Question

Question:

Have a double place yacht club pwc trailer.. In need of new springs.. The measurement is about 30 3 leaf slipper springs,,, Trailer GVWR is 1550.. What do you recommend for replacement? Thanks again

asked by: Paul F

0

Expert Reply:

For a 30 inch slipper spring replacement for a PWC trailer that has a GVWR of 1,550 lbs the best option is the part # e29SR which is 30 inches long and is rated for up to an 1,800 lb trailer axle.

expert reply by: Jameson C

0

Answer 1

Yes the slipper spring part #e29SR that you referenced can install below the trailer axle. I attached a picture that shows it installed in this orientation.

view full answer...

Answer 2

The Dexter Trailer Springs Over-Under Conversion Kit part #K71-384-00 CAN be used with slipper springs. However, the process of installing this kit on a trailer with a set of slipper springs is more in depth than installing this kit on a trailer…

view full answer...

Answer 3

We have a couple of slipper springs that may work for you, as they are 1-3/4 inches wide, measure a total of 30 inches, and have the capacity you need. Springs do elongate over time, but you may have to have your brackets re-positioned if the 30 inch…

view full answer...

Answer 4

The weight rating on the #SP-039275 spring would be 1500lbs per side, with a rating of 3000lbs for both sides. I have included some more information on installing slipper springs, if needed.

view full answer...

Answer 5

I would be happy to help! First you will need to measure the slipper springs on your 1982 TeeNee trailer from the center of the spring eye to the end of the spring as shown in the included diagram, and the width of the spring. You will need to jack…

view full answer...

Answer 6

The best slipper spring option for your Triton PWC trailer is going to be the Slipper Spring part #SP-039275 as it's for up to a 2,900 lb axle, is a 3-leaf setup, and is 1-3/4 inches wide. It does have a flat end though and not a radiused end but…

view full answer...

Answer 7

The 3-Leaf Slipper Spring w/ Flat End part #SP-039275 is rated for up to 2,900 lbs when used as a pair so these will work great on a 2,200 lb axle. They will be a bit stiffer than the factory leaf springs but this also means there will be more…

view full answer...

Answer 8

The most important factor in picking out a new leaf spring for a trailer is to match the capacity needed. Going with a 3,500 lb spring for a 2,100 lb trailer is going to give you a very harsh ride. For a spring similar to the #WIG4 that is better…

view full answer...

Answer 9

We have the replacement slipper springs you are looking for. They are the 3-Leaf Slipper Spring w/ Flat End for 2,900-lb Trailer Axles - 30" Long, #SP-039275. These have a spring capacity of 1,450 lbs and an axle capacity 2900 lbs.

view full answer...

Answer 10

The best option we have is the part #SP039275 that you referenced. It's going to be a little longer and a little stiffer than you need most likely since it's for a 2,900 lb axle, but it will work and get the job done.

view full answer...

Answer 11

The length of the slipper spring is from the center of the eye to the end of the slipper. See the attached diagram below. The width and the capacity are also necessary when choosing a replacement, leaf count isn't very important and can vary. The…

view full answer...

Answer 12

It sounds like you are needing the Nylon Bushing #TRBU11561 for your EZ Loader trailer leaf springs. These bushings have an outside diameter of 1.024" and a inner diameter of 9/16". The bushing is 1-3/4" wide. As long as the inner…

view full answer...

Replacement 30 inch Slipper Spring for PWC Trailer with 1,550 GVWR

Product Page this Question was Asked From

Continue Researching