Bolt Hole Spacing for Curt Class V Commercial Duty Trailer Hitch Receiver

Question

Question:

can you tell me hole spacing on this hitch CURT 15845 i have found it is for a 34 in wide frame looking for hole spacing and can not find that info thanks

asked by: Henry W

0

Expert Reply:

I definitely have a photo of the dimensions for the Curt Trailer Hitch Receiver # C15845!

In the attached photo you'll see the spacing varies between 30" and 31" depending on which set of mounting holes you're looking at.

expert reply by: Jon G

0

Mounting Hole Dimensions for Curt Hitch C15845
(click to enlarge)

Answer 1

The Curt Trailer Hitch Receiver part #C15845 that you referenced is a confirmed fit for a 2016 Ford F-550 cab and chassis with frame rails spaced 34" apart (outside to outside). However, Curt does not test this trailer hitch with dump body…

view full answer...

Answer 2

Since your truck's frame is 34 inches from outside to outside it was definitely a cab and chassis truck at the beginning of it's life which is what the Curt hitch part #C15845 was designed to fit. From the top of the receiver crosstube of…

view full answer...

Answer 3

The Curt Trailer Hitch Receiver - Custom Fit - Class V Commercial Duty - 2-1/2" #C15845 will come down about 8 inches from the frame. It does add some support to help with an underrun in a rear end collision so as long as the drop is enough but…

view full answer...

Answer 4

Curt 2-1/2-inch Class V hitch #C15845 will fit the 1999 Ford F-450 cab and chassis so long as the frame width (measured outside to outside) is 34-inches. Drilling is required for installation. I went to our warehouse and measured the side-to-side…

view full answer...

Answer 5

We have the Curt hitch part #C15845 which fits your 2016 Ford F-450 Cab and Chassis and is a 2-1/2 inch trailer hitch. This has a capacity of 20,000 lbs too.

view full answer...

Answer 6

The distance from the top of the receiver to where it would mount on the bottom of the truck is 6" on the #C15845 Curt Trailer Hitch Receiver. The distances between the mounting bolts vary so I am attaching a picture showing the different…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

Generally speaking wheel mount only bike racks are preferred. Especially for people with carbon fiber bike frames since frame mounts aren't recommended at all with them otherwise damage could occur. For other frame designs people still prefer…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Bolt Hole Spacing for Curt Class V Commercial Duty Trailer Hitch Receiver

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching