How to Measure For Heat Duct Vent Register

Question

Question:

How Doo I measure for heat duck in my 210 Forest River Sterling 5th wheel need one for my bathroom. Do I measure the hole or the vent? Thanks

asked by: Barbara

0

Expert Reply:

What you want to do is measure the access hole for your heat duct register, and get one that fits the hole size. For example, if it was 4" x 10" you'd use the Dampered RV Floor Register # 37202-29175, or if it was 4" x 8" you'd use the Dampered RV Floor Register # 37202-29155.

I have added a link below to our entire selection for you which you can filter by size.

expert reply by: Kyle S

0

Answer 1

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 2

We do have exactly what you need, with floor registers that have interior dimensions (the opening) of 8 inches long and 4 inches wide; you even have your choice of color: - Black: Dampered RV Floor Register #37202-29155 - White: Dampered RV Floor…

view full answer...

Answer 3

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on…

view full answer...

Answer 4

Yes, the best option we can offer you to add fuel capacity is with the DeeZee Truck Bed Auxiliary Tank part #DZ91752X which should fit in the space you have between the cab and 5th wheel hitch no problem as it is only 9" deep. I…

view full answer...

Answer 5

To determine which brake assemblies would be needed, you will need to measure your existing brake drums as shown in the provided photo. Since your trailer has a 14,000 lb capacity, you most likely have tandem 7,000 lb axles, which typically use a…

view full answer...

Answer 6

As far as height adjustability and weight capacities the Curt Q20 #C16130 and the Curt A20 #C16140 are identical. They both have a Gross Towing Weight of 20,000 lbs, a Vertical Load Limit of 5,000 lbs, and a height range of 13-17 inches. When it…

view full answer...

Answer 7

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The…

view full answer...

Answer 9

I checked with Curt and they do show the Curt Trailer Hitch Receiver part #C13233 as a fit for a 2022 Volvo XC90 All Models which includes the Recharge.

view full answer...

Answer 10

If you have already added the fuse and the trailer charge circuit is not activated in the 2019 Ford F-350 Super Duty with factory integrated brake controller, then you want to make sure the trailer is connected and you press the brake according to…

view full answer...

Answer 11

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and…

view full answer...

Answer 12

I took a look at the owner's manual for a 2019 GMC Sierra 1500 Denali and both it and the standard 1500 can be flat towed so long as it is a four-wheel drive with a two-speed transfer case, and according to page 236 of the manual,…

view full answer...

How to Measure For Heat Duct Vent Register

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching