Do You Have a Backing Plate For The Tandem Axle Teardrop Trailer Fenders # HP94VR?

Question

Question:

Do you sell a backing plate for this fender?

asked by: Jud F

0

Expert Reply:

The Backing Plate # HP72FR can be used with the Tandem Axle Teardrop Trailer Fenders # HP94VR. These backing plates are 69" by 12" and manufactured from 18 gauge steel. It can be cut if you are wanting to match the profile of the fenders.

expert reply by: Bud M

0

Answer 1

The Tandem Axle Trailer Fenders - Double Radius - Steel - 14" to 15" Wheels - Qty 2 #HP94VR are 65" long x 9" wide x 15" tall and they are designed to work with 33 to 35 inch on center axle spacing.

view full answer...

Answer 2

The Tandem Axle Teardrop Trailer Fender #HP94VR you were looking at is 9" wide the whole length of the fender, and at it's largest is 15" deep/tall.

view full answer...

Answer 3

I have a solution for you but no we do not have any tandem steel fenders with the backing plate already welded into place. I recommend the Tandem Axle Teardrop Trailer Fenders for Enclosed Trailers - 14" to 15" Wheels item #HP24VR…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Do You Have a Backing Plate For The Tandem Axle Teardrop Trailer Fenders # HP94VR?

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching