Tandem Axle Fenders and Backing Plates

Question

Question:

Am looking at HP94VR. I need something like this, but I need them to have inner steel panel. Is this additional P.N. piece or do you have fender with inner panel already welded in place? Thanks in advance for your help and Blessings!

asked by: Jon W

0

Expert Reply:

I have a solution for you but no we do not have any tandem steel fenders with the backing plate already welded into place. I recommend the Tandem Axle Teardrop Trailer Fenders for Enclosed Trailers - 14" to 15" Wheels item # HP24VR and the Backing Plate for Tandem Axle Trailer Fender - Steel - 68-7/8" Long x 12" Tall item # HP92FR. These fenders come in a pair and are 9" Wide x 72" long x 20-1/2" tall. These sturdy teardrop fenders have a flat back to mount flush with your trailer. They are made out of 16-Gauge, cold-rolled steel. And can be bolted or welded onto your trailer. The curved backing plate prevents water and road debris from hitting the side of your trailer. These come in singles so you will need to purchase two. I have attached a couple of review videos of these products.

expert reply by: Jerred H

0

Answer 1

The Backing Plate #HP72FR can be used with the Tandem Axle Teardrop Trailer Fenders #HP94VR. These backing plates are 69" by 12" and manufactured from 18 gauge steel. It can be cut if you are wanting to match the profile of the…

view full answer...

Answer 2

The Tandem Axle Trailer Fenders - Double Radius - Steel - 14" to 15" Wheels - Qty 2 #HP94VR are 65" long x 9" wide x 15" tall and they are designed to work with 33 to 35 inch on center axle spacing.

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...