Replacement Hitch Hardware Plates for Draw-Tite Hitch 24873 on 2016 Fiat 500

Question

Question:

Do you have the 2 top plates for sale that fit the draw tite class 1 hitch for a 2016 fiat 500? I have all of the other parts but am missing the 2 top plates and want to avoid buying a complete unit if possible. If not do you have 1/4 x 3 x 14 long flat steel plates for sale?

asked by: Robert F

0

Expert Reply:

I do have an option for you but we don't offer individual pieces of hardware for any one trailer hitch. If this is all you need then you'd have better luck at a local hardware store. That said, we do offer complete kits that come with all the hardware that the hitch would have come with when new. The Replacement Trailer Hitch Hardware Kit part # RHK comes with the 3-1/16" wide x 6-3/4" long x 3/16" thick plates when ordered for the Draw-Tite Sportframe Trailer Hitch Receiver part # 24873.

expert reply by: Conner L

0

Answer 1

I have attached a chart you can check out that describes the torque needed per wheel size, wheel stud size and material. For an 8-inch wheel with a 1/2-inch wheel stud the torque is 75 to 86 ft-lbs. For a 15 inch steel wheel with 1/2 inch wheel studs…

view full answer...

Answer 2

The only option I have to offer replacement hardware for a trailer hitch is with the Replacement Hardware Kit for Trailer Hitches part #RHK which is the same as the original hardware. In order to get the correct hardware for the Curt Trailer Hitch…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Replacement Hitch Hardware Plates for Draw-Tite Hitch 24873 on 2016 Fiat 500

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching