Replacement Brake Shoe Lining for 10" Hydraulic Trailer Brakes

Question

Question:

I just need the brakes, no springs or adjusters.. for right and left.. please contact me info if possible.. Thanks

asked by: Brent C

0

Expert Reply:

It sounds like you're wanting replacement brake shoes for your assemblies which I assume is to save some money but unfortunately, the cost of new shoes versus new assemblies is marginal which is why almost everyone just goes with new assemblies. Furthermore, unless you know exactly what brand of assemblies you have we would not be able to offer any options as they are brand specific whereas new complete assemblies are not. The Hydraulic Trailer Brake Kit part # AKUBRK-35 is truly your best option if you're looking for 10" hydraulic brakes.

expert reply by: Conner L

0

Answer 1

The etrailer.com Hydraulic Trailer Brake Kit #AKUBRK-35 referenced in your question has a 4 bolt mounting flange pattern, as you mentioned. The mounting hole dimensions are 4 inches diagonally across and 2-7/8 inches left to right. This is the…

view full answer...

Answer 2

Yes, the hydraulic brake assembly part #AKUBRK-35L is the correct assembly you need for the left side of the trailer. For a set that includes both sides of the axle what you need is the part #AKUBRK-35. These assemblies are for the standard 10 inch…

view full answer...

Answer 3

The e-coat on the #AKFBBRK-35 is basically a paint that uses an electrical current to apply it to the surface. The Dacromet coating on the #AKFBBRK-35-D is a water-based adhesive coating made of zinc and aluminum flakes. The part is dipped in the…

view full answer...

Answer 4

If you cannot find a sticker or plate on your boat trailer axle you can still get in the ballpark on its weight rating based on the brake dimensions. All of our 10 x 2-1/4-inch drum brakes, both electric and hydraulic, that work with 14-inch trailer…

view full answer...

Answer 5

The Galvanized Demco Hydraulic Brake Kit #40716-15 is definitely the best coating that you can get for corrosion resistance. The other coatings are basically just different levels of powder coats while galvanized resists salt water much better. I do…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…

view full answer...

Replacement Brake Shoe Lining for 10" Hydraulic Trailer Brakes

Product Page this Question was Asked From

Continue Researching