Mounting Flange Bolt Pattern of Etrailer.com Hydraulic Trailer Brake Kit AKUBRK-35
Question:
Trying to ensure the correct product, the description is lacking. for item AKUBRK-35 it says 4 bolt mounting flange, but what size? other suppliers indicate the bolt pattern, 2-1/2inch square for example...so what pattern is this flange?
asked by: Mike
Helpful Expert Reply:
The etrailer.com Hydraulic Trailer Brake Kit # AKUBRK-35 referenced in your question has a 4 bolt mounting flange pattern, as you mentioned. The mounting hole dimensions are 4 inches diagonally across and 2-7/8 inches left to right. This is the standard 4 bolt pattern for trailer spindles.
This hydraulic brake kit is designed for 3,500 pound axles and will fit wheel sizes of 13-15 inches. Both the left hand and right hand assemblies are included.
I have attached a short video demonstration on this product for you to check out.
Product Page this Question was Asked From
Hydraulic Trailer Brake Kit - Uni-Servo - 10" - Left and Right Hand Assemblies - 3,500 lbs
- Trailer Brakes
- Hydraulic Drum Brakes
- Standard Grade
- Manual Adjust
- Single Servo
- 10 x 2-1/4 Inch Drum
- 3500 lbs Axle
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- etrailer
more information >
Continue Researching
- Shop: Hydraulic Trailer Brake Kit - Uni-Servo - 10" - Left and Right Hand Assemblies - 3,500 lbs
- Shop: Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles - Qty 2
- Shop: Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Video: etrailer Hub And Drum Assembly Installation
- Video: Titan Brake Actuator T2374600 Review
- Shop: Replacement Master Cylinder Assembly for Dexter Model 10 and Model 20 Brake Actuators - Drum
- Shop: Replacement Master Cylinder and Push Rod Assembly for Drum Brakes - Model 10 and 20 Actuators
- Search Results: axle grease caps
- Video: etrailer Hydraulic Trailer Brake Kit Installation
- Shop: Demco Hydraulic Drum Brake Assembly - Free Backing - Galvanized - 10" - Right Hand - 3,500 lbs
- Search Results: trailer bearings races seals caps
- Video: etrailer Trailer Hub and Drum Assembly Installation AKHD-545-35-K
- Q&A: Replacement Hydraulic Drum Brakes for Trailer with 10-Inch Hub/Drums
- Q&A: Replacement Brake Shoe Lining for 10" Hydraulic Trailer Brakes
- Video: Titan Master Cylinder Assembly Installation
- Q&A: Replacement Titan Master Cylinder that is Stamped 23744
- Video: Review of Dexter Axle Brake Actuator - Master Cylinder and Pushrod - DX66FR
- Search Results: 23744
- Search Results: hydraulic brake shoes
- Search Results: brake line fittings
- Search Results: brake line
- Search Results: fittings
- Q&A: How to Measure to Determine the Correct Grease Seal for a Trailer Spindle
- Video: Review of etrailer Trailer Hubs and Drums - Hub with Integrated Drum - AKHD-545-35-K
- Q&A: Replacement Hydraulic Surge Brake Brake Assembly
- Q&A: Is The Hydraulic Trailer Brake Kit a Pair of Brakes?
- Q&A: Recommended Replacement for Atwood Surge Brake Actuator 85778
- Article: How to Tell the Weight Rating of a Trailer Axle
- Article: How to Bleed Your Trailer Surge Brakes