Is There a Replacement for a Dexter 5,200 Lb 93" Long Axle

Question

Question:

I am looking for a specific Dexter axle. Serial number 121075483. Are you able to use this # to search? I will consider other brands as long as they are the same spec.

asked by: Jerry

0

Expert Reply:

I do have an option for you though we don't have a direct replacement for this axle. The closest we have is the Trailer Axle Beam part # e63GR which measures 95" at the hub or 80" at the spring center. It will stick out about an 1" more per side than the existing and you'll need to cut and reweld the spring seats a few inches. It has the same 5,200 lb capacity as you have now so you can reuse any existing hubs.

In order to obtain an exact replacement, you'll need to reach out to Dexter directly.

expert reply by: Conner L

0

Is There a Replacement for a Dexter 5,200 Lb 93" Long Axle
(click to enlarge)

Answer 1

It's definitely possible to upgrade a trailer's axle rating to a higher rating by just swapping the axles. To pick out the correct axle you'll need to measure the distance between the hub faces and the spring seat centers and you'll…

view full answer...

Answer 2

Most if not all trailer wiring harnesses/connectors use larger wires for the 12 volt and ground circuits compared to the other circuits (lights). The sockets themselves don't have an amperage rating so you will go by the draw of the things…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 9

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Is There a Replacement for a Dexter 5,200 Lb 93" Long Axle

Product Page this Question was Asked From

Continue Researching