Trailer Axle Beam with Easy Grease Spindles - 95" Long - 5,200 lbs
(172 reviews)
Price: $358.88
In Stock
Trailer Axle Beam with Easy Grease Spindles - 95" Long - 5,200 lbs
Item # e63GR
Our Price: $358.88
In Stock
- All Info
- Reviews (172)
- Q & A (0)
- Photos
etrailer Trailer Axles - e63GR
- 5200 lbs
- 95 Inch Long
- 80 Inch Long
- Spindles Only
- No Drop or Lift
- Leaf Spring Suspension
- No Hubs
- etrailer
- Easy Lube Spindles
Round trailer axle beam measures 95" from hub-face-to-hub-face (when hubs - sold separately - are mounted) and 80" from spring-center-to-spring-center. Easy Grease spindles make it easy to lubricate bearings (sold separately).
Features:
- Round axle beam acts as part of your trailer's suspension system
- Replace an axle on your trailer
- Fabricate a suspension to fit your application
- High-strength steel construction
- Bend in axle creates zero camber angle for even road-to-tread contact across the width of your trailer's tires
- Best for straight-line acceleration and steady, controlled towing
- Underslung design - spring seats welded to underside of axle for mounting leaf springs (sold separately)
- Low ride height makes it easier to load and unload your trailer
- Straight, Easy Grease spindles - no drop
- Patented welding process prevents spindle failure with 40% stronger welds
- Built-in grease zerk for simple lubrication
- Spring seats and spindles are welded on
- CSA, QAI, and SAE-N certified
- Lifetime technical support from the experts at etrailer.com
- Made in the USA
Specs:
- Weight capacity: 5,200 lbs
- Hub-face-to-hub-face length: 95"
- Spring-center-to-spring-center length: 80"
- Axle diameter: 3"
- Spindle/hub compatibility:
- Bearings: 25580 inner, 15123 outer
- Seal: GS2250-DL, inner diameter 2.25"
- Limited lifetime warranty
Axle Dimensions
There are multiple ways to measure the length of an axle beam, but the hub-face-to-hub-face and spring-center-to-spring-center lengths are the most accurate. Hub face (A) refers to the length of the axle measured from the base of one wheel stud to the base of the wheel stud on the opposite side of the axle (when hubs are mounted on the beam).
The spring center (B) is the approximate width of your trailer. It is measured from the center of the spring seat on one side of the axle to the center of the seat on the other. This axle beam comes with the spring seats welded on.
If you are replacing your trailer's axle, you should be able to figure out which type you need by determining your trailer's capacity, the bolt pattern of your wheels, the brake type and the aforementioned lengths.
etrailer Axles
etrailer axles are made of high-strength steel and come with spindles and spring seats welded on. The spring seats are attached to the underside of the axle so that the leaf springs (sold separately) can mount beneath the axle. The result of this underslung design is a trailer that rides a bit lower for quick and easy loading and unloading.
Each axle is manufactured to create a certain camber angle. This ensures that the angle of the wheels is correct for your towing needs. Because the primary concern when towing is maintaining controlled, in-line movement, each axle is made so that your trailer's tires will run along the pavement evenly, with contact across the width of the tread. The result is excellent straight-line acceleration for steady, in-line tracking. You might notice the bend near the center of the axle; this is what ensures the proper camber angle. Having the center ride a bit higher and the sides of the axle bent lower allows the axle to give just enough to compensate for the load.
e63GR etrailer by AxleTek Replacement Axle Beam - Easy Grease - 95" Hub Face - 80" Spring Center - 5,200 lbs
Customer Satisfaction Score:
98% were satisfied with this product
2% of customers were not satisfied
- Wrong item was ordered
- etrailer mistake
Customer Reviews
Trailer Axle Beam with Easy Grease Spindles - 95" Long - 5,200 lbs - e63GR
Average Customer Rating: 4.7 out of 5 stars (172 Customer Reviews)
Round trailer axle beam measures 95" from hub-face-to-hub-face (when hubs - sold separately - are mounted) and 80" from spring-center-to-spring-center. Easy Grease spindles make it easy to lubricate bearings (sold separately).by: Gina10/19/2023
Everything is working perfect with that replacement axle. I have definitely put it to the test a lot of miles with a lot of weight. Very highly recommended.
by: Jerry 07/16/2023
Direct replacement for my rusted out axles on my car trailer, perfect fit, awesome quick shipping thanks etrailer
by: Mike11/03/2023
A+ works great. Fast shipping if I ever need axle again will buy from you
by: Norris 10/24/2023
This axle fit and has done a great job for the loads it has hauled
by: Ricky 01/14/2022
Got 3 5200 lb axles pretty fast love the price love the quality all of them come with brake flange and they come prewire inside pipe for brakes also the crown nut is included better deal cannot be found
Highly recommend them
by: John 02/25/2023
Very Heavy duty axle
by: Bob 01/10/2023
Excellent product
by: Peter 09/04/2022
Good quality, fast shipping
by: William10/15/2022
Item fit perfectly
by: Alisa05/08/2023
by: Matt 08/23/2022
by: Darriel07/04/2022
by: Jeff 10/21/2022
by: Mark B10/04/2022
by: Robert 08/26/2021
by: Jason05/30/2023
The axles that I ordered last year are still working out great. But even better than the parts was the service I got from etrailer. It was so great working with a company who took the time to listen to my project and help me get the right parts I needed, especially coming right off the heels of a terrible experience dealing with bad information and wrong parts from a competitor. Even with some damages in shipping, the returns/ and replacements were no hassle, with most issues being quickly resolved and not even costing me any additional downtime. As a contractor keeping a small fleet rolling, your competency and professionalism have made me a customer for life!! You guys at etrailer will be my first stop for trailer parts.
by: 11/30/2023
Welds looked good however the assembler failed to rotationally align the weld on spindle/brake mounts properly. One was about 3 degrees off and the other side was an 9.5 degrees from the 12 oclock position. Not sure about the thickness of the tube. Kind of strange to look at when the top of the brake system is not at 12 oclock. Found this after I removed the spring pads on this 2.1 degree camber axle so I had to jig the tube to fine zero toe to locate the new pads as the 2.1 camber tube changes wheel alignment depending on the bend/ springpad relationship. Not sure the AVG JOE is going to be able to move the spring pads when the brake mounts can't be used as a reliable ref point. If the toe is off from improper pad rotational location. the trailer will eat tires at best or worse cause a loss of controlled tracking and someone could get get killed.
by: John04/26/2024
Replaced the old axles with these on my 7x16’ equipment trailer, been nothing but amazing since I’ve installed them. Hauled thousands of pounds since and with minor greasing and normal maintenance they’ve been great.
by: Mark04/16/2023
So far performing well. Have not been able to use trailer yet as much as I wanted to, don't use the grease nipples. Its easy to regrease without.
by: Josh03/08/2024
I haven’t installed the axle yet, but it looks to be pretty solid. Time will tell. Irrelevant to the axle, but I have to touch up some paint where UPS dropped it down on my concrete. Not a big deal though. It’s going to get beat up by road debris anyway.
by: Tom 11/17/2022
Very easy installation. Everything fit perfect.
by: Patrick 04/16/2024
Always hair free when I buy from ev tra iler
by: Bob W02/08/2024
The mounts were 1/2 inch closer than advertised. I was able to persuade the springs inward to compensate. Good price and fast shipping.
by: Terry07/11/2023
Axle arrived fast, was exactly what I ordered and needed. Install went well with no problems.
by: Ralph03/07/2024
Received. Cannot use till all parts come
25
170
Show More Reviews
See what our Experts say about this etrailer Trailer Axles
- Is There a Replacement for a Dexter 5,200 Lb 93" Long AxleI do have an option for you though we don't have a direct replacement for this axle. The closest we have is the Trailer Axle Beam part # e63GR which measures 95" at the hub or 80" at the spring center. It will stick out about an 1" more per side than the existing and you'll need to cut and reweld the spring seats a few inches. It has the same 5,200 lb capacity as you have now so you can reuse any existing hubs. In order to obtain an exact replacement, you'll need to reach out to Dexter...
view full answer...
- Is There a Hub Conversion Kit for Mobile Home Axle to Accept Standard Wheels/TiresI might have an option for you but mobile home axles are a one-time only use part and there aren't any hub conversion kits available for them to use standard wheels/tires that I am aware of. If you need the trailer mobile again you'll have to replace the axles with modern ones that allow for standard wheels/tires. I have created a great video for you to assist with this and then you can use the attached selection or our axles and wheels/tires to setup the trailer for use again. The Trailer...
view full answer... - What is the Physical Difference of a 5,200 lbs Axle and a 6,000 lbs Axle?The only physical difference of a 5,200 lbs axle item # e63GR and a 6,000 lbs axle item # e73GR is in the custom bend in the axle. This bend creates the zero camber angle for even road to tread contact. Both axles are 3" in diameter so they have the same thickness. As far as spindles go they both fit a item # 25580 inner bearing and a item # 15123 outer bearing.
view full answer... - Recommended 95" Long 5,200 Lb Trailer AxleThe best option we have for this is the Trailer Axle Beam with Easy Grease Spindles part # e63GR which has a 5,200 lb capacity, 95" hub face length, and 80" spring center length. If you need a different spring center length you can easily cut the old ones off and weld on part # TRSS300.
view full answer... - How Much Weight Can 5,200 Pound Trailer Axles HoldThe percent of the rating you can use for your 5,200 lb axle is 100%. The axles on your tandem axle trailer are designed to hold 5,200 lbs each or 10,400 lbs total. As long as you are not exceeding this amount there is no reason to increase axle capacity with the # 7461121. Also, other components on your trailer, and more than likely the trailer frame, are rated for the same. Even with a higher axle capacity you will be limited by the weakest component. If you're looking for a 95" 5,200...
view full answer... - How to Determine Correct Replacement Axle, Bearings & Brakes For Big Tex TrailerWe can help tell you how to determine the correct replacement axle, brakes and bearings for your Big Tex trailer but have no way of knowing exactly what you need. In order to choose the correct replacement axle for your trailer you will need to know the dimensions of your current axle's hub face to hub face and spring center to spring center; I have added a link below to a video which walks you through how to measure. The other thing you need to know is the weight capacity of the axle you...
view full answer... - Recommend Trailer Axle Replacement For A 1988 20 Foot TrailerWhen it comes to replacing the axle on your 1988 20 foot trailer, we currently do not have a 4,500 pound axle replacement. We do have the next size up in a 5,200 pound axle that would work if you meet some measurement requirements. We would need to know the hub face to hub face dimension and would also need to know the spring center to spring center measurement. We currently have 3 different sizes: The Dexter Trailer Axle Beam 86-1/2 inches # 8327816 The Dexter Trailer Axle Beam 89...
view full answer...
- Replacement 5,200 Pound Axle for Forest River Enclosed TrailerFor a 95" 5,200 lb replacement axle you can use the # e63GR. None of our axles match that spring seat measurement so you will need to cut off the spring seats and weld on # TRSS300 to match your current measurement. If you meant a 4" drop spindle when you said "with 4," the only replacement option for the same length axle would be a 3,500 lb axle like the # 7685269. This would again need new spring seats # TRSS238. If you're set on 5,200 lbs and need the 4" drop you could use the Timbren...
view full answer... - What Hubs Would Work With The etrailer Axle # e63GRThe Trailer Axle Beam with Easy Grease Spindles - 95" Long - 5,200 pounds # e63GR has an inner bearing # 25580 and the outer bearing # 15123 will have a 6 by 5-1/2 bolt pattern. The Easy Grease Trailer Hub and Drum Assembly for 5.2K & 6K Axles - 12" - 6 on 5-1/2 - Pre-Greased # AKHD-655-6-EZ-K will match up perfectly with the 5,200 to 7,000 pound axle # e63GR. The Trailer Axle Beam with Easy Grease Spindles - 89" Long - 3,500 pounds # e38GR has an inner bearing # L68149 and the outer...
view full answer...
Do you have a question about this Trailer Axle?
Info for this part was:
Edited by:
Lindsey S
Video by:
Jacob T
Video Edited:
Chris R
Updated by:
Leah S
Updated by:
Wilson B
Updated by:
Kristina F
Updated by:
Noah M
Updated by:
Carrie F
Installed by:
Conner L
Installed by:
Michael B
Written by:
Mike S
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.