How Many Catalytic Converters Are Installed in 2002 Lexus ES300

Question

Question:

How many catalytic converters does this model have? I was told it has two or maybe three.

asked by: ToSHanna H

1

Helpful Expert Reply:

The 2002 Lexus ES falls into the 4th generation of this design and if equipped with a 3.0L V6 engine it has three catalytic converters, according to my contact at MagnaFlow.

The front converter is part # MF50821. The rear converters are parts # MF26214 and # MF50260. These are all bolt-on products; no welding is required. None of these items are approved by the state of California.

I have linked each of these parts, but please note that the product images on our web pages are not the exact images for these products. In a separate linked photo I have included the actual manufacturer images for each of these three items.

I have also included for your reference several articles concerning catalytic converters.

expert reply by: Adam R

1

click to enlarge

Answer 1

Although the Dexstar Steel Mini Mod Trailer Wheel #AM20315 has a e-coat primer and black powder coat finish, this is option is much more prone to rust over an aluminum or galvanized rim. The powder coat finish is mainly for common trailer use so it…

view full answer...

Answer 2

If you are absolutely sure that's your bolt pattern we don't have any spare wheels and tires that will fit, but we do know that the industry standard bolt pattern for 14 inch trailer wheels is 5 on 4-1/2 inch so most likely that is what you…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 8

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 9

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...