Does Yakima Backswing Pivoting Hitch Adapter Come with Locking Hitch Pin

Question

Question:

Can you lock the Yakima Backswing to you receiver hitch, maybe with locking hitch pin?

asked by: Rick

0

Expert Reply:

Yes you can, the Yakima Backswing pivoting hitch adapter part # Y02483 that you referenced actually comes with a locking hitch pin too so you wouldn't need to get one separately.

expert reply by: Jameson C

0

Answer 1

If the nut is stripped inside the anti-rattle insert that is included in the Replacement Hitch Bolt, Nut and Clip for BigHorn 4 Bike Carrier #Y8780022 then you will need to purchase a new kit. Anytime there is a replacement option for equipment…

view full answer...

Answer 2

I measured the bolt that is included in the Yakima Replacement parts kit #Y8780022 and found it has the following dimensions: Overall Length 4-5/8 Hex Head Size 13/16 Thread diameter 1/2 Length of Thread 2-1/2 I prepared a photo with these…

view full answer...

Answer 3

As long as your 2020 Toyota Highlander XLE has a 2" hitch receiver then the Yakima BackSwing #Y02483 will work just fine and allow you to install a bike rack that swings away from the back of vehicle. It looks like all of the available…

view full answer...

Answer 4

I see the movement you are referring to in the attached video. The Yakima BackSwing Swing Away Hitch Extender #Y02483 will likely add some form of bounce or movement compared to not using it at all since it adds a few components and moving parts to…

view full answer...

Answer 5

I believe you are asking for the replacement hitch bolt for your Yakima BackSwing Swing Away Hitch Extender #Y02483, which is something that we do carry: - Replacement Hitch Bolt, Nut and Clip #Y8780022 I did verify for you with Yakima that this is…

view full answer...

Answer 6

The Yakima HD bars do have a channel on the top of them that a Thule Hullavator part #TH898 could easily attach to. There's a cover that's on them which is designed to lower wind noise but that easily comes off and is trimmable. So for a…

view full answer...

Answer 7

It sounds like you have the Yakima HD crossbars similar to the #Y01156. These are attached and held in place by the HD Bar SL Adapter #Y03541 on your roof rack towers and the #Y03541 would be the correct way to replace one of those. The HD Bar SL…

view full answer...

Answer 8

The Curt cargo carrier part #C18100 is a lighter weight carrier due to it being made mostly out of aluminum. For a lighter weight option for your 2019 Tesla Model X with a hitch like the Draw Tite part #76143 installed this would be a really great…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof racks.…

view full answer...

Does Yakima Backswing Pivoting Hitch Adapter Come with Locking Hitch Pin

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching