Parts Needed to Install Autowbrake and 7-Way for Towing with a 2016 Toyota RAV4

Question

Question:

I need to install a 7-pole connector on my 2016 RAV4 Hybrid. I did not find any guidance on how to install a 7-pole connector. I plan to use a Autowbrake controller as my brake controller. Can you refer me to some resources to setup the 7-pole connector? I currently have a 4-pole connector installed on my vehicle.

asked by: Emlyn H

0

Expert Reply:

To use the Autowbrake with your 2016 Toyota RAV4 you need the following parts:

7-Way RV Upgrade Kit - # ETBC7L
Curt No-Drill Bracket - # C57202
Autowbrake Electric Brake Controller - # 3430001
Junction Box and Installation Kit - # 3430001-JBK

The 7-Way kit plugs into your 4-Way and then has a power lead that connects to the battery on your RAV4 which is needed for the Autowbrake, and the Curt bracket is needed to hold the 7-Way plug near your hitch receiver. Then the junction box gives you a nice, clean way to organize the wires on your trailer when you splice in the wiring for the Autowbrake installation.

expert reply by: Jon G

0

Answer 1

I reached out to my contact at AutoWBrake and he was able to confirm that the Autowbrake Electric Brake Controller #3430001 can be installed onto the rear of a vehicle like you mentioned. He mentioned that it was tested in that manner during…

view full answer...

Answer 2

Aside from the Curt Echo #C51180 that you referenced that does not require running the blue brake output circuit from the 7-way of your vehicle up to a brake controller mounted in the interior of your vehicle we also have the Autowbrake #3430001…

view full answer...

Answer 3

You are correct, the first thing you will need to do is add the #ETBC7 Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires. This kit will provide you with everything you need to turn your 4-way into a…

view full answer...

Answer 4

To add a 7-way connector to your 2020 Subaru Outback I recommend the #ETBC7L which will plug into your existing 4-way connector and will only require you to make two connections, grounding the white tire to the frame of your vehicle, and running the…

view full answer...

Answer 5

Installation of a brake controller on your 2022 Subaru Outback Limited XT will not void the warranty. Hopefully the dealer isn't on crack, but even if they are you're protected under the Federal Magnusson-Moss Warranty Act. Basically, if…

view full answer...

Answer 6

The majority of the complaints with the Curt Echo Mobile Trailer Brake Controller part #C51180 not being secure have a lot to do with the factory trailer connector they are being used with. These factory trailer connectors do not hold the same levels…

view full answer...

Answer 7

Both of these are reliable brake controllers. Personally I like the freedom that the Curt Echo #C51180 gives you. You can use it on any vehicle with a properly wired 7-way and trailers with up to 2 braking axles. There is no wiring and it can be…

view full answer...

Answer 8

Since the Autowbrake part #3430001 needs a 12 volt power source to function properly you would need to convert your 4-way to a 7-way with the part #ETBC7L which comes with parts needed to activate the 12 volt accessory circuit of the 7-way for the…

view full answer...

Answer 9

I went out to the warehouse and measured the Curt Echo Wireless Trailer Brake Controller - 1 to 2 Axles - Proportional part #C51180. I have attached a diagram of the measurements for your reference. If you have the space I recommend to use the Curt…

view full answer...

Answer 10

To answer your first question, there isn't a traditional "adapter" to allow the 7 way on your trailer to plug into a 4 way connector on your vehicle- at least not in the manner that you're thinking of. For that reason you would…

view full answer...

Answer 11

You can absolutely use the Redarc Tow-Pro Liberty Brake Controller #RED24FR in your 2023 Subaru Outback. But you will need the Universal Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers #RED69FR for installation. There may be a few more…

view full answer...

Answer 12

Since your 2021 Toyota Rav4 Prime has a factory 4-way all you need to convert it to a 7-way and install the Curt Echo Mobile brake controller part #C51180 is the part #ETBC7L which comes everything needed. This would be same solution you'd need…

view full answer...

Parts Needed to Install Autowbrake and 7-Way for Towing with a 2016 Toyota RAV4

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching