Diameter of Bolt of Ultra Fab Roller Wheel # UF48-979022

Question

Question:

What is the construction of the wheel and pin? Is there a bearing? If so, is the bearing sealed? It would be good to have a cross-section view. If there is not a bearing, what is the ID of the roller, if we want to use a shoulder bolt that has been drilled and cross-drilled for lubrication?

asked by: Vince A

0

Expert Reply:

There is no bearing in the Ultra Fab roller part # UF48-979022. It's basically a solid roller with a 5/8 inch diameter hole that a 5/8 inch diameter bolt runs through.

expert reply by: Jameson C

0

Answer 1

The #UF48-979022 steel mini-roller is sold individually. If you wanted a pair, you'll want to order two of them. For a bolt-on application, take a look at #UF48-979017 which is sold in pairs. If you click the provided link, you can see product…

view full answer...

Answer 2

I went out to the warehouse and pulled roller #UF48-979022 to take some measurements. The overall height is actually 2-13/16 inches. The wheel does have a 2 inch diameter. The mounting bracket itself is 2-5/16 inches across and 2 inches front to…

view full answer...

Answer 3

I went out to our warehouse to take a look at the Ultra-Fab Steel Mini-Roller #UF48-979022 referenced in your question. I was able to confirm that the bolt hole is exactly a 1/2 inch in diameter. The wheel itself is not available as a separate item…

view full answer...

Answer 4

Another wire or harness is not needed on the 2023 Honda CR-V for the install of the Curt 4-Way Wiring Harness #C56370, but you do have to add 20 amp fuse to location #17 in the fuse box.

view full answer...

Answer 5

Hello Gaby. I reached out to the manufacturer and found out that the UltraFab Weld-On Jumbo Steel Roller #UF48-979023 uses a 6-1.0mm Zerk fitting. For a replacement you can use the following: - Replacement Brass Grease Zerk for Weld-On Hinges - 6 mm…

view full answer...

Answer 6

For your application there really is only going to be a weld on solution that's reasonable like the part #UF48-979022 that you referenced. The frame dimensions are unknown so a weld solution would be better since that really doesn't matter.…

view full answer...

Answer 7

I did some looking and found that the 46210 and 46845 hubs you currently have use the same #L68149 inner bearing and #L44649 outer bearing. However, as we do not carry the Tie Down Engineering Vortex hubs, I cannot say what all will fit them,…

view full answer...

Answer 8

The Dexter 8-222 model hubs currently on your trailer are designed primarily for mobile home use, and these types of hubs typically use unique bearing combinations that make it really difficult to find full replacement assemblies. Mobile home parts…

view full answer...

Answer 9

The Trailer Hub and Drum Assembly part #AKHD-545-35-K is the correct replacement for an AL-KO 7230. In regards to the braking assemblies, I suggest getting a new pair, the Electric Trailer Brake Kit part #AKEBRK-35-SA. This option will save you some…

view full answer...

Answer 10

Yes, the etrailer #e67ZR tow bar is made for etrailer by Demco in the USA and has a lifetime limited warranty by etrailer. Demco parts will work on this tow bar, but Demco has no responsibility for warranty, repair, or service - you would need to go…

view full answer...

Answer 11

Thank you for reaching out! A standard flat towing setup requires a base plate kit, tow bar, safety cables, vehicle tow bar wiring, a supplemental braking system, and possibly a high-low adapter. Here is what I recommend using for your 2022 Jeep…

view full answer...

Answer 12

The Dexter 8-427 hub is no longer available. Even looking through Dexter's site the only references to it are replacement bearings. You can use a wheel with a larger pilot hole as long as the wheel attaches to the hub using lug nuts and not…

view full answer...

Diameter of Bolt of Ultra Fab Roller Wheel # UF48-979022

Product Page this Question was Asked From

Continue Researching