What are the Dimensions of the Ultra-Fab Steel Mini-Roller for Trailers and RVs UF48-979022

Question

Question:

the dimensions of these products contradict themselves it says overall height is 2 1/2inch and wheel diameter is 2 1/2 lets assume the diameter is correct and the plate is 1/4inch and there is a 1/4inch gap between the steel and the wheel that would mean 2.5+0.25+0.25 for a height of 3 what are the real dimensions?

asked by: Jason

0

Expert Reply:

I went out to the warehouse and pulled roller # UF48-979022 to take some measurements. The overall height is actually 2-13/16 inches. The wheel does have a 2 inch diameter. The mounting bracket itself is 2-5/16 inches across and 2 inches front to back. I have included a picture with the dimensions for you.

expert reply by: Michael H

0

click to enlarge

Answer 1

There is no bearing in the Ultra Fab roller part #UF48-979022. It's basically a solid roller with a 5/8 inch diameter hole that a 5/8 inch diameter bolt runs through.

view full answer...

Answer 2

The #UF48-979022 steel mini-roller is sold individually. If you wanted a pair, you'll want to order two of them. For a bolt-on application, take a look at #UF48-979017 which is sold in pairs. If you click the provided link, you can see product…

view full answer...

Answer 3

I went out to our warehouse to take a look at the Ultra-Fab Steel Mini-Roller #UF48-979022 referenced in your question. I was able to confirm that the bolt hole is exactly a 1/2 inch in diameter. The wheel itself is not available as a separate item…

view full answer...

Answer 4

Another wire or harness is not needed on the 2023 Honda CR-V for the install of the Curt 4-Way Wiring Harness #C56370, but you do have to add 20 amp fuse to location #17 in the fuse box.

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Hello Gaby. I reached out to the manufacturer and found out that the UltraFab Weld-On Jumbo Steel Roller #UF48-979023 uses a 6-1.0mm Zerk fitting. For a replacement you can use the following: - Replacement Brass Grease Zerk for Weld-On Hinges - 6 mm…

view full answer...

Answer 7

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

For your application there really is only going to be a weld on solution that's reasonable like the part #UF48-979022 that you referenced. The frame dimensions are unknown so a weld solution would be better since that really doesn't matter.…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Sag is a pretty common problem for trucks towing a 5th wheel trailer, so SumoSprings are a smart idea, and the best option for your 2021 Ram 3500 are the following: - SumoSprings Rebel Custom Helper Springs #SSR-301-47-2 The SumoSprings #SSR-301-47-2…

view full answer...

Answer 12

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...