Installation Instructions for a Stealth Hitch Being Installed on a 2023 Kia Telluride

Question

Question:

Im looking at a 7 way setup for a 2023 Kia Telluride Item # 391CONVPT5L. Im not seeing any instructions on your site. Is there any available? Also is there a T for the wiring that I am not seeing or do I need to just hard wire into the harness?

asked by: Joshua V

0

Expert Reply:

We do not have the instructions for the Towing Kit w/ Ball Mount item # 391CONVPT5L but I was able to find an installation video for the Stealth Hitches Hidden Trailer Hitch Receiver w/ Towing Kit item # 391KIATELL20T and have linked it below. This is for the hitch and the towing kit you referenced. The instructions are included with the hitches or are available on Stealth Hitches website.

As of 02/26 there are no custom fit wiring harness options for the 2023 Telluride. You will want to use the Curt Powered Tail Light Converter item # C59236 to add a 4-way connector and then the item # ETBC7 to add a 7-way.

expert reply by: Jerred H

0

Answer 1

I spoke with Lippert and they said the Kwikee 35 Series Electric RV 1-Step part #LC3691461 will be a direct replacement for the Coach Steps 725-0041. It will be a bolt-on install for the most part for the exception of changing out the door switch…

view full answer...

Answer 2

You're correct that the Progressive Dynamics Inteli-Power RV Converter and Battery Charger - 12V - 30 Amps #PD9130 would be the correct replacement for your BW Manufacturers Inc. 3230 Converter/Charger but you may also need a new DC fuse board as…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 10

As far as wiring for the 2024 Toyota Grand Highlander, we do have the Curt #C59236 available which is more of a universal hardwire harness. Unfortunately there are not any plug-and-play options that have been confirmed to fit as of yet (October 4,…

view full answer...

Answer 11

I do have a solution for your 2024 Kia Telluride that has the LED taillights that does allow it to have both a 4-way and 7-way plus install a brake controller but it is not with the #TK74CR which does not work for you based on the LED taillights.…

view full answer...

Answer 12

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...