Torque Specs For the Leg Bolts On The Curt A25 5th Wheel Hitch

Question

Question:

I purchased the Curt 25k 5th wheel hitch for my 2017 GMC Sierra 3500 in 2018, but forgot the torque specs for the 5th Wheel bolts that attached the side legs to the 5th wheel. Do you have that information?

asked by: Paul D

0

Expert Reply:

According to Curt's instructions, the torque specs for the leg bolts on the Curt A25 5th Wheel Trailer Hitch for Chevy/GMC Towing Prep Package # C16066 is 100-ft.lbs.

I've also included an install video on a 2018 Chevrolet Silverado 3500 for you to check out as well.

expert reply by: Bryce D

0

Answer 1

Thank you for your purchase of the Curt A16 5th Wheel Trailer Hitch #C16120 from etrailer, and the two bolts on the side of the head unit #C16520 should not be coming loose. According to Curt, you should make sure those two bolts are torqued to 175…

view full answer...

Answer 2

Oh wow, that's definitely not a good experience but I'm glad you made it home safely! The bolts that hold the rotating skid plate to the Rota-Flex pin box, like part #LC328329, are definitely Grade 5 bolts and although I'm unsure which…

view full answer...

Answer 3

Pin box bolt torque is based on the size of the bolts. 1/2 inch Bolts GR5 90 ft-lbs 5/8 inch Bolts GR5 150 ft-lbs 3/4 inch Bolts GR5 275 ft-lbs

view full answer...

Answer 4

The linked instructions for your Curt Class III Trailer Hitch #13364 indicate the torque specifications for both the included 10mm and 12mm fasteners. These specs are listed as item 4 in the instructions. For reference I have linked you to an…

view full answer...

Answer 5

It sounds like you need to re-calibrate the zero point on your Lippert Ground Control 3.0 #LC304136 system. Below I've listed out the steps you'll need to follow and will allow you to use the auto leveling again. Zero Point Calibration The…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 9

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 10

Hey Jay. It sounds like you are on the right track here because a sidewinder pin box will be your only option for pulling your 5th wheel since you have a short bed truck with the Rambox. That said, you are right that the Reese Sidewinder cannot be…

view full answer...

Answer 11

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 12

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 you're looking at will work fine with your new Chevrolet Silverado. This hitch has 3 height adjustments so you'll be able to set the hitch height…

view full answer...