Adapter For Connecting EZ Connector 14 Pin Trailer Connector To 7-Way Blade Vehicle Conector

Question

Question:

Is there an adapter to go to traditional 7way when using a vehicle without mag plug?

asked by: Nick

0

Expert Reply:

The EZ Connector Magnetic 14-Pin Trailer Connector # 319-S14-07-6 will fit inside the Trailer Connector Adapter # EZ94ZR and plug into a truck with a 7-way blade connector. You only need the 14-Pin Vehicle End Connector # 319-S14-05-6 for any functions over the standard 7 to function. We do also have the Adapter # 319-R7-52 which will fit inside the vehicle side connector allowing you to tow a trailer with a 7-way blade connector.

expert reply by: Bud M

0

Answer 1

The Trailer Connector Adapter with Cable - EZ Connector to 7-Way RV - Trailer End item #EZ94ZR does work with 7-way vehicle connectors no matter what vehicle they are on. You will have no problem connecting the 7-way trailer end of the trailer…

view full answer...

Answer 2

The EZ Connector Magnetic 7-Way Trailer Connectors #319-R7-02 you found uses a vehicle side connector which tee's into the vehicle wiring. This allows you to retain your factory 7-way and be able to connect to either the included magnetic…

view full answer...

Answer 3

Thank you for all of the information and your photo! It really looks like you've done your research with all of the various solutions you've looked at to try to prevent damaging the connection between your Lance Truck Camper and your 2019…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 10

I do have a solution for your 2024 Kia Telluride that has the LED taillights that does allow it to have both a 4-way and 7-way plus install a brake controller but it is not with the #TK74CR which does not work for you based on the LED taillights.…

view full answer...

Answer 11

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 12

Whether or not you can flat tow with a Jeep bumper is really up to the manufacturers testing; some of the big names like MetalCloak or Poison Spyder have bumpers with D-ring attachments that can be used for flat towing connections. This is great…

view full answer...