Replacement Dutton-Lainson 90-946 100VDC 7.7 Motor

Question

Question:

I would like remplace my motor 90-946 100VDC 7.7 What the price and delay?

asked by: Claudia

0

Expert Reply:

To replace the 90-946 100VDC 7.7 motor on your Dutton-Lainson winch you need the part # DL304921. The current pricing and shipping options can be found on the product page directly.

expert reply by: Jon G

0

Answer 1

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 2

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 3

Since you have a Dometic AC unit the best option to replace it from Advent would be the part #ACDOM135 which was designed for this exact situation and would allow you an easy install since the electronics would plug right in.

view full answer...

Answer 4

Yes, to replace the motor on your Dutton-Lainson powered winch you just need the part #DL304921. This the exact 90-946 100VDC 7.7 max amp motor you are needing.

view full answer...

Answer 5

We have a great option in a replacement 45 amp power converter for your ELX-45. I suggest the Progressive Dynamics, #PD4045KA. This is a 2-in-1 AC/DC distribution panel and smart charger that works with lithium-ion, flooded lead acid, AGM, and gel…

view full answer...

Answer 6

Slipper spring setups, like parts #e74SR and #APT6SE for 7K axles, do have different hanger sizes so what you'll want to do is cut off the older hangers and do some mock-ups of your new system before installing the hangers. Start off by mocking…

view full answer...

Answer 7

I spoke with Furrion about the Furrion Microwave FMSMA15-SS and they informed me that the Furrion Over the Range RV Convection Microwave part #FMCM15SS is the correct replacement. I verified all of the dimensions and power ratings for you as well to…

view full answer...

Answer 8

The Husky Brute Jacks like #HT87247 had some models with remote like you referenced. You may want to start by removing the battery from the remote in case it is actually giving a slow retraction signal. Although that is unlikely, it is worth a shot.…

view full answer...

Answer 9

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Answer 10

The spring hanger placement is going to be determined by your axle spacing. For example, if your axles are spaced 33 inches apart, as shown in the attached diagram, a 7K axle slipper spring, like #e74SR, requires a distance of 28-1/2 inches between…

view full answer...

Answer 11

Yes, you can use the Furrion Chill HE RV Air Conditioner System - Manual - 15,000 Btu - White #FR92PR to replace your old 68RV15102A.

view full answer...

Answer 12

The black wire from the break away switch will connect to the blue wire from the break away box, as shown in the provided diagram. By 'brake wires' I'm assuming you're speaking of the wires connected to the brake magnets on your brake…

view full answer...

Replacement Dutton-Lainson 90-946 100VDC 7.7 Motor

Product Page this Question was Asked From

Continue Researching