Replacement Manual Switch For Pace Edwards Bedlocker Tonneau Cover

Question

Question:

I have a Pace Edwards bed locker model BL2022 serial 060616683 and am looking for a replacement bed mounted open/close rocker switch, I need only the switch. Can you help with this? Thanks Joe

asked by: Joe F

0

Expert Reply:

To replace the rocker switch on your Pace Edwards Bedlocker Tonneau cover you'll need the Manual Switch Kit for Pace Edwards BedLocker # 311-BL-1120.

expert reply by: Kevin C

0

Answer 1

Replacement key fobs are available for Pace Edwards powered retractable tonneau covers, but we'll need to know the model number in order to find the correct fob for you. The Replacement Remote #PE33QJ for example, is compatible with the Bedlocker…

view full answer...

Answer 2

For a Pace Edwards Bedlocker tonneau cover you would need the Replacement Remote for Pace Edwards Bedlocker Retractable Hard Tonneau Cover #PE33QJ. Pace Edwards also has the Manual Switch Kit for Pace Edwards BedLocker or UltraGroove Electric Tonneau…

view full answer...

Answer 3

There are some replacement parts available for the Pace Edwards BedLocker tonneau cover. There is a Replacement Tailgate Top Seal for Pace Edwards Retractable Tonneau Covers #PE99CV and there is also the Manual Switch Kit for Pace Edwards BedLocker…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The manual switch for the Pace Edwards Bedlocker Retractable Hard Tonneau Cover #PE44CV can be found as part #311-BL-1120 on our site. This plugs into the harness at the canister and then you route and install the switch wherever it works best for…

view full answer...

Answer 12

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Replacement Manual Switch For Pace Edwards Bedlocker Tonneau Cover

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching