Colors of Lock and Unlock Wires For Pop & Lock Installation on 2017 Chevy Silverado 1500

Question

Question:

What color wires do I splice into so the 12v part of poplocks will operate with the factory power locks

asked by: Mark

0

Expert Reply:

According to the Pop & Lock vehicle wiring chart, the lock wire is tan and the unlock wire is blue or gray on your 2017 Silverado 1500. However, you will need to verify this using a circuit tester like the # PTW2993. The lock wire will have power when the lock button is pushed and the unlock will have power when the unlock button is pushed. The red wire on the # PAL9555 connects to the lock wire and the black wire connects to the unlock wire.

expert reply by: Robin H

0

Answer 1

The Leer 100XR isn't specifically listed by Pop and Lock but more than likely the #PAL9772 will fit. It requires a frameless, bonded glass door with a 1-1/8" center hole for a rotary latch. This particular kit would upgrade your…

view full answer...

Answer 2

You can use 7-way trailer wiring with the module part #PP20-702 to provide power to the third brake light of your camper shell/cap. Basically the stop/turn circuits of the trailer wiring need to run to the yellow wires of this module and then the…

view full answer...

Answer 3

The logic box that you are asking about is our Pacer Performance 3rd Brake Light Logic Module #PP20-702. This is a piece of equipment that is required when using an LED light as a 3rd brake light. If there is a specific light style that you are…

view full answer...

Answer 4

The lock and unlock wires on your 2011 Chevrolet Silverado will be a tan and a gray wire located under the sill plate in the wiring harness that goes under the drivers side seat. I spoke with my contact at Pop and Lock and he said the tan wire can…

view full answer...

Answer 5

The Pop & Lock Power Lock Conversion Kit for Truck Caps and Hard Tonneau Covers #PAL9772 will work on the A.R.E. MX series truck cap you referenced on your 2017 Ford F-250 Crew Cab Short Bed. This will give you a clean look along with the…

view full answer...

Answer 6

Yes, this kit #RRRk059-2 is for the 059 locking core so if that's what you have on your roof then these will unlock it for removal.

view full answer...

Answer 7

Depending on if you have a crew cab or not the instructions for the Pop & Lock Power Lock Conversion Kit for Truck Caps and Hard Tonneau Covers #PAL9772 lists the lock wire as Tan and the unlock wire as Blue (Gray for crew cabs). They also…

view full answer...

Answer 8

For a topper lock that ties into the power lock system of a truck we have the part #PAL9555 which would work well on your hard tonneau cover that you have installed on your 2017 Chevy Silverado 1500.

view full answer...

Answer 9

The brake signal is run along with the blinker on separate wires. The passenger side is normally green and carries the right turn and brake light. The driver's side is normally yellow and carries the left turn signal and brake. The…

view full answer...

Answer 10

The best product we have for wiring third brake lights in a camper shell is the 3rd Brake Light Logic Module part #PP20-702. If you were to combine this with an in-bed wiring harness such as the Curt 5th Wheel/Gooseneck Custom Wiring Harness part…

view full answer...

Answer 11

The correct lock and unlock wires to splice into on a 2016-2019 GMC Sierra to install the Pop & Lock Power Locking Handle for Truck Caps and Hard Tonneau Covers part #PAL9555 should be a tan with a yellow stripe and grey. That said, it is…

view full answer...

Answer 12

Sounds like your air bag setup has a slow leak that is causing the compressor system to try and keep up too often. You should take some soapy water and spray on the bag, lines and where it connects to the Air Lift Compressor part #AL74000 to see if…

view full answer...