Torflex Lift Kit for a Single Dexter Axel P 12 SLR Axle

Question

Question:

Hello, Can you please help, trying to get a lift kit for Single Dexter Axel P 12 SLR. I do ha e pics just didnt know how to attach! Hopefully you can help .... Thanks again ..

asked by: Arturo L

0

Expert Reply:

Thanks for the information it looks like you have a #12 Torflex axle. You're going to need the Torflex Lift Kit item # K71-725-02. They do not offer any single axle lifts so you will have an extra set.

The Torflex Lift Kit # K71-725-02 provides 3-1/8" of lift.

If you would like to email me those pictures I will be happy to take a look at them and confirm this is compatible with your 2000 Jayco Qwest Camper.

expert reply by: Jerred H

0

Answer 1

Manufacturers don't keep detailed records of the specific parts that are on year, make and model of trailers, and since those parts could have changed over the years the only way to know if the Torflex Lift Kit #K71-725-02 will work for you is if…

view full answer...

Answer 2

I went out into the warehouse to measure the Lift Kit #K71-725-02 for you. The holes measure 9 inches on center and 9-1/2 inches on center. I've attached a photo to assist.

view full answer...

Answer 3

I reached out to my contact at Dexter Axle who said that your axle is rated for 3,500 lbs and it uses inner bearing #L68149, outer bearing #L44649, and the grease seal #58846. All of these can be found in the kit #BK2-100 if you are needing to…

view full answer...

Answer 4

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 5

Finding the correct MORryde equalizer kit will be pretty specific, so I cannot tell you which will be correct without knowing the wheel spacing and axle capacity, unfortunately. With that being said, if you have the trailer's VIN, you may be able…

view full answer...

Answer 6

Yes, going from a 4 leaf to a 6 leaf spring would add slightly to your ride height. For example, if the current 4 leaf spring has 3/8" thick leaves, and you go to a 6 leaf spring with 3/8" thick leaves, you would be adding 3/4" of…

view full answer...

Answer 7

Based on the available information for your 2022 Airstream Flying Cloud 30FB it looks like you have Dexter #11 Torflex axles. Assuming that is accurate, you need the Torflex Lift Kit - Tandem Axle - 2-7/8" Lift #K71-724-02. I recommend verifying…

view full answer...

Answer 8

Hi Bruce, To lift your trailer we'll first need to check of the suspension and see if you have torsion axles or a leaf spring suspension. If you have torsion axles then I'll need to see the axle tag in order to determine what you have so I…

view full answer...

Answer 9

I sent your axle info to Dexter and they were able to determine that you have a set of 7k Dexter Torflex axles so the correct lift you need is the part #K71-725-02 which will give you a lift of 3-1/8 inches.

view full answer...

Answer 10

Thank you for the pictures! I reached out to my contact at Dexter Axle who was able to confirm that you have #11 Torflex axles so the correct lift kit is part #K71-724-02. Since yours has top mounting holes you also need the bracket kit #DX57FR for…

view full answer...

Answer 11

Thanks so much for the photo that was super helpful, and what the axle tag shows is that you have a #11 Dexter Torflex axle. We do have the correct lift kit for you, which is the following part: - Torflex Lift Kit - Tandem Axle #K71-724-02 This kit…

view full answer...