Wire Coding For Pollak 7-Pole Trailer Wiring Socket # PK11720

Question

Question:

Which is reverse? Center purple wire?

asked by: Mark A

0

Expert Reply:

When looking at The Pollak 7-Pole Trailer Wiring Socket # PK11720 at the six O'clock position is where the purple reverse light connects. I will attach a picture below showing all the functions of the socket.

expert reply by: Noah E

0

Pollack Wiring Diagram
(click to enlarge)

Answer 1

Based on the images you sent in it appears your 2005 Starcraft RT10 does not use a traditional A-Frame coupler so the Lock N Roll #336TS504 will not work for your application. Instead you will need to measure the width between your frame rails the…

view full answer...

Answer 2

This is a really good question! So it turns out there are two ways that 7-way wire colors are ran. The one like what you described is considered 7-way traditional whereas the other style is considered RV standard. I attached a diagram that hopefully…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 7

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

The 8-14.5 tires are an older metric size no longer used today. Therefore, you would need to replace these along with the wheels in order to update them. In order to see if we have any options for you, we'd first need to determine the bolt…

view full answer...

Answer 10

The Ark Drop Down Corner RV Stabilizer Jacks #ARK94FR are able to lock into place at 30 and 60 degrees as stabilizers. They also have the 90 degree position where it is rated for 1,929 lbs and then the stored position.

view full answer...

Answer 11

The Lock N Roll Articulating Coupler #336TS504 dimensions for the A-frame are 2.19" at the narrowest part and 11.22" at the widest part of the opening. It is 9.68" long from largest opening to narrowest. I have included a picture below…

view full answer...

Answer 12

You are correct that the Jeep bracket should have been reinstalled when installing the Blue Ox Base Plate #BX1139. I have linked another video near the bottom of the page where you can see the brackets being reinstalled on a 2020 Jeep Wrangler around…

view full answer...

Wire Coding For Pollak 7-Pole Trailer Wiring Socket # PK11720

Product Page this Question was Asked From

Continue Researching