Replacement Seals for Waste Valves Which are Difficult Operate

Question

Question:

How can I mobilize a valve that is difficult to open and close?

asked by: Nikolas J

0

Expert Reply:

Often times when a Waste Valve # T1003PBC becomes difficult to operate the seals need to be cleaned and lubed. We also have Replacement Seals for 1-1/2" # T1001-9VP, 2" # T1002-7VP and 3" # T1003-9VP valves if they are damaged. New hardware is included with these seals as it typically corrodes.

expert reply by: Bud M

0

Answer 1

Remove the locknut from the cable housing assembly of the #34466N11AB96GMA. Feed the cable through the mounting bracket or hold in the wall of chassis. Feed the locknut back over the cable and fasten securely to the backside of the bracket or wall.…

view full answer...

Answer 2

It is completely within the realm of possibilities that the actuator has become disconnected from the gate internally causing the valve to not open. The Valterra Waste Valve Body for RV Black Water Tank w/ Coupler, Seals, and Hardware - 3"…

view full answer...

Answer 3

The valves you are seeking to replace are made by many different manufacturers and are a standard size. The function of the valve is what you want to pay attention to as there are T-handle and cable options and then of course black water versus gray…

view full answer...

Answer 4

It sounds like you're looking for the Valterra Waste Valve Body for RV Black Water Tank part #T1003PBC and Valterra Waste Valve for RV Gray Water Tank part #T1001PBC. These will accept your old cables so you don't have to worry about…

view full answer...

Answer 5

I do have an option for you, however the exact valve body that is included with the Valterra Waste Valve w/ Flexible Cable #TC372 you mentioned is not available as a separate part from the manufacturer. What you can use instead is the Valterra Waste…

view full answer...

Answer 6

Hey Douglas, The Valterra Bladex RV Waste Valve Seals #T1001-9VP are slightly larger (thicker) than the LaSalle Bristol gate valve seals so you while you could get them to fit you'd likely have a leak over time. Your best bet would be to replace…

view full answer...

Answer 7

The part #T1001-9VP is specifically designed for the Valterra Bladex Waste Valves like part #T1001VPM. If you have a typical 1-1/2" waste valve then you want to go with part #T1001-7VP instead.

view full answer...

Answer 8

The gray water tank valve on the Bristol Double RV Waste Valves part #34466ND13AAR can be replaced using the Bristol Waste Valve Body for RV Gray Water part #34439241 or the Valterra Bladex Waste Valve Body for RV Gray Water Tank part #T1001VP. If…

view full answer...

Answer 9

Go ahead and send me the pictures and I'll take a look to see which 1-1/2 inch Valterra seal you would need. The biggest visual difference is that the new Bladex Style part #T1001-9VP has a small lip on one corner of it that's used for…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

For your 2018 Ram 2500 with the factory puck system the best 5th Wheel Hitch is the B&W OEM Companion. If you have the 8 foot bed then you will want the fixed 25K #BWRVK3600 and if you have the short 6-1/2 foot bed you will need the 20K Slider…

view full answer...

Answer 12

The Carrier Air V RV Air Conditioner is no longer produced so a direct replacement of the same unit is not an option. However, we do have available the two Advent AC models that are designed as replacement units for the Carrier Air V. I recommend…

view full answer...