Replacement Grey Water Body/Seals for Bristol Double RV Waste Valves 34466ND13AAR

Question

Question:

Hi: Sorry to trouble you again. Since I can just replace the black tank valve. I will also like to replace the seal for the gray tank valve at same time. Can you give me the # for this item. Yes, you said I have the #66ND13AAR termination setup. Thank you

asked by: Randy L

0

Expert Reply:

The gray water tank valve on the Bristol Double RV Waste Valves part # 34466ND13AAR can be replaced using the Bristol Waste Valve Body for RV Gray Water part # 34439241 or the Valterra Bladex Waste Valve Body for RV Gray Water Tank part # T1001VP. If you just want the seals then that would be the Valterra Bladex RV Waste Valve Seals part # T1001-9VP.

expert reply by: Conner L

0

Answer 1

Yes, the handle for the Bristol Waste Valve Body for RV Gray Water #34439241 is threaded onto the rod so it can be removed like what you're needing.

view full answer...

Answer 2

Often times when a Waste Valve #T1003PBC becomes difficult to operate the seals need to be cleaned and lubed. We also have Replacement Seals for 1-1/2" #T1001-9VP, 2" #T1002-7VP and 3" #T1003-9VP valves if they are damaged.…

view full answer...

Answer 3

I would love to help but I do not have any information that tells me what size drain pipes are on your 2007 Keystone Passport Ultralite so you will need to measure this for yourself. The standard size is 1-1/2" for the grey water tanks and…

view full answer...

Answer 4

Yes, you can replace the 3" and 1-1/2" valves on your Bristol Double RV Waste Valves - Elbow - Rotating - 3" and 1.5" Hubs to 3" Spigot #34466ND14AAR with the Bristol Waste Valve Body for RV Gray Water w/…

view full answer...

Answer 5

Hey Douglas, The Valterra Bladex RV Waste Valve Seals #T1001-9VP are slightly larger (thicker) than the LaSalle Bristol gate valve seals so you while you could get them to fit you'd likely have a leak over time. Your best bet would be to…

view full answer...

Answer 6

The Bristol Waste Valve Body part #34439241 is 1/2" thick. This will work perfectly in place of the valve you have attached a photo of. The 1-1/2" opening and four bolt mounting flange are both industry standards so you won't have any…

view full answer...

Answer 7

The part #T1001-9VP is specifically designed for the Valterra Bladex Waste Valves like part #T1001VPM. If you have a typical 1-1/2" waste valve then you want to go with part #T1001-7VP instead.

view full answer...

Answer 8

Go ahead and send me the pictures and I'll take a look to see which 1-1/2 inch Valterra seal you would need. The biggest visual difference is that the new Bladex Style part #T1001-9VP has a small lip on one corner of it that's used for…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Replacement Grey Water Body/Seals for Bristol Double RV Waste Valves 34466ND13AAR

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching