Availability of Valterra Waste Valve Body without Cable

Question

Question:

Can the tc372 valve only be purchased with out cable

asked by: Joe

0

Expert Reply:

I do have an option for you, however the exact valve body that is included with the Valterra Waste Valve w/ Flexible Cable # TC372 you mentioned is not available as a separate part from the manufacturer.

What you can use instead is the Valterra Waste Valve Body # T1003PBC. This is a very similar valve body that will work the same as what is included with the kit you mentioned. The body features a 3 inch diameter passage to allow wastewater to travel when it's open and the body, seals, Allen wrench, and hardware are all included. As long as you already have the needed cable and housing this will work great.

I have attached a short video demonstration that you can also check out.

expert reply by: Chris R

0

Answer 1

According to Valterrra, if your #TC1372 waste valves are fully closing, but are still leaking you'll want to replace the seals. You'll need both the 3 inch seal kit, part #T1003-9VP and the 1-1/2 inch seal kit, part #T1001-9VP

view full answer...

Answer 2

It sounds like you're looking for the Valterra Waste Valve Body for RV Black Water Tank part #T1003PBC and Valterra Waste Valve for RV Gray Water Tank part #T1001PBC. These will accept your old cables so you don't have to worry about…

view full answer...

Answer 3

Often times when a Waste Valve #T1003PBC becomes difficult to operate the seals need to be cleaned and lubed. We also have Replacement Seals for 1-1/2" #T1001-9VP, 2" #T1002-7VP and 3" #T1003-9VP valves if they are damaged. New…

view full answer...

Answer 4

The waste valve part #T1003PBC is designed to be used with a cable handle like #TC96PB for a 96 inch cable or #TC72PB for a 72 inch cable. These are all black handle as there isn't a gray handle setup for this valve.

view full answer...

Answer 5

The Valterra Waste Valve #T1003PBC is designed to be used with a cable handle so it will work well for you.

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 9

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 10

A 4-way trailer connector will have four functions which means it will also have four wires for the exception of wishbone harnesses. These four functions are ground, tail light, right turn, and left turn. The ground function will usually be…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...