Replacement Bearings And Races For Agricultural Hub

Question

Question:

Im needing to replace my axle hub assembly, Hub is EWC D24D 6 Lug, Inner bearing LM48548 Outer bearing LM67048

asked by: Kaleb N

1

Helpful Expert Reply:

What you have is an agricultural hub assembly. We will not have a replacement hub but we do offer replacement bearings and races.

Inner Bearing # LM48548
Inner Race # LM48510
Outer Bearing # LM67048
Outer Race # LM67010

expert reply by: Noah E

1

Answer 1

The fact your outer bearing fits on a .75 diameter spindle means we aren't going to have a standard bearing kit to fit since that's not a standard dimension. Can you get me the C dimension as well? It could be that you need the part…

view full answer...

Answer 2

From the measurements you gave me, it sounds like you have an Agricultural Spindle like #TRU54FR that uses #LM67048 Inner bearing and #LM11949 Outer bearing. For a hub assembly with a 4 on 5 bolt pattern #AH15450ECOMP will work and the bearings,…

view full answer...

Answer 3

If the leaf spring part #e57SR that you referenced matches up dimensionally to what your trailer has and has a capacity that is 400 lbs more than needed it would work just fine. Having a bit extra capacity for the leaf springs would not cause an…

view full answer...

Answer 4

We usually tell people to look for about 3 inches of clearance to account for the total travel capabilities of trailer suspension. If you have less than 3 inches you might be able to compensate by using slightly longer shackle straps. I have included…

view full answer...

Answer 5

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 6

The #TRU84FR spindle is rated for 3,500 pounds and uses bearings #L68149 and #L44649. We have some 6-lug hubs that fit but they aren't 6 on 6 they're 6 on 5-1/2 like part #AKHD-655-35-EZ-K. We only carry two hubs with a 6 on 6 pattern and…

view full answer...

Answer 7

You should be able to replace the wheel stud, but you'll need to drive the stripped stud out and get the measurements shown in the provided diagram in order to locate the correct replacement. You'll need a drift punch that is smaller in…

view full answer...

Answer 8

The 175/80-13 tire that you have now is 24" diameter x 6.9" wide and the new 225/75-15 tire is 28.3" diameter x 8.9" wide. Therefore, the new tire size will be 4.3" larger in overall diameter and 2" larger in overall…

view full answer...

Answer 9

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 10

We have wheels for the 4 on 9.44 inch bolt pattern like #AM20395 but we don't carry any hubs to fit them. If you are able to pull a hub and get the bearing numbers which are printed on the face of the inner and outer bearing I may be able to help…

view full answer...

Answer 11

The first thing to try to is add some penetrating oil like WD40 and let it sit for awhile. You can then try tapping the bearing to try and remove it. You don't want to hit it too hard because you can damage the spindle. It is possible that the…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Replacement Bearings And Races For Agricultural Hub

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching