Height Adjustable Side Mount Bolt On Trailer Jack

Question

Question:

RDJ-2K The Ultimate Trailer Jack - A-Frame - Weld On or Bolt On - Topwind - 27-1/2 Travel - 2,000 lbs Do you have one of these that is a side bolt on, kind of like a swivel type but not a swivel type. Thanks

asked by: Thomas G

0

Expert Reply:

The side mount bolt on ARK Xtreme Off-Road Swing-Up Trailer Jack # ORJW750D has a similar height adjustment to the Ultimate Trailer Jack # 322-RDJ-2K. The ARK jack does have a dual wheel and 1,650lb capacity versus the plate and 2,000lb capacity of the Ultimate jack. The ARK does have the ability to swivel as we do not have exact equivalent jack like the Ultimate that bolts on the side frame.

expert reply by: Bud M

0

Answer 1

This is a great question! Although we do list the ball hole diameter in the specs for each ball mount, there is an easier way to make sure a ball mount has the hole size you need. Any ball mount rated for Class IV hitches will have a 1-1/4"…

view full answer...

Answer 2

I have a recommendation for you as the Ultimate Trailer Jack #322-RDJ-2K you found is our best solution for moving the jack out of the way for a tail gate. Instead it is much easier to switch to a ball mount with a longer shank like the Brophy…

view full answer...

Answer 3

The a-frame trailer jacks all use a standard mounting pattern and center hole size for the most part so although I am not quite sure what you are measuring I can confirm we have options, the Ultimate Trailer Jack part #322-RDJ-2K is a good one…

view full answer...

Answer 4

The Ultimate Trailer Jack part #322-RDJ-2K is the lowest profile trailer jack and would work great for you. Since the bracket is adjustable you can set the height of the jack at a very low height as needed.

view full answer...

Answer 5

I do have an option for you but I don't have any way to reduce the ground clearance of your existing a-frame jack . That said, what you can do to fix this issue is replace your existing jack with the Ultimate Trailer Jack part #322-RDJ-2K.…

view full answer...

Answer 6

Since we don't have a jack quite tall enough for you really tall trailer the best option we have would be the #ORJW750BD with the wheel chock for jacks part #FT11933MI to help take up the extra room.

view full answer...

Answer 7

I have a couple options for you to consider as no one makes a jack that will bolt on in place with your Shelby 4587 jack bracket you have welded to your frame. First the Round Swivel Marine Jack w/ Wheel #MJ-1200B is the closest we have to the…

view full answer...

Answer 8

The Xtreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels #ORJW750BD has an extended bracket height of 29-5/8 inches. The maximum height when moving a trailer is 23-1/2 inches. It has a static load capacity of 1,650 pounds and has a dynamic load…

view full answer...

Answer 9

The mounting plate on the Dutton-Lainson Round Swivel Jack part #DL22335 has bolt holes which are 7/16" diameter. The bolt holes are spaced 5-1/2" apart on center from top to bottom and then in 1" increments apart working your way from…

view full answer...

Answer 10

The Dutton-Lainson Square Swivel Jack #DL22340 has a mounting plate designed to fit trailer frames with a height of 3" - 5". I have attached a dimensional drawing below with all of the bolt spacing for your reference.

view full answer...

Answer 11

I have a solution to your question. For the Dutton-Lainson Bolt-On, Drop Leg Trailer Jack, #DL22320, I have attached a photo of the mounting bracket. We have measured the bracket and the distances of the mounting holes and marked them for you in the…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...