Erickson E-Track 5 Foot Installation on a Utility Trailer for Hauling a Golf Cart

Question

Question:

Just purchased a 2013 Aluma Utility trailer to haul my EZGO golf cart around. After trying to tie the cart down via the roll bar and eventually the frame, the ratchet tie downs came loose both times. I have decided to go w/ tire tie downs and the e-track tie down system. My main concern is the installation of the E-track on to the aluminum floor. What is the best way for me to install the e-track? How do I do this? What additional parts do I have to purchase to get this done? Thanks,

asked by: Rod

0

Expert Reply:

To install the Erickson E-Track 5 foot section # E19148 on your trailer you can use rivets, screws, or weld it to the trailer. Since your trailer is aluminum, welding may not be an option since the E-Track is steel. I recommend using screws, or bolts and nuts, and backing plates like the etrailer # e96RR.

Another option that some of our other customers have done, is to use additional E-Track on the bottom of their trailer, and liked the option of having additional tie down locations. (Rob's review on 6/4/2012 product # E19148)

You would install either the backing plates, or additional E-track, on the under side of the trailer to line up with the mounting holes on the E-Ttrack. Make sure that you use screws or bolts and nuts that are the correct strength rating and dimensions. The mounting holes on the E-Track are 1/4 inch in diameter and are spaced 2 inches apart on center.

Also keep in mind, when mounting the E-track make sure that your attachment hardware is also secured to the frame and or crossmembers of the trailer.

You can then use the wheel strapping system of your choice. I have included links to these parts as a couple of videos for your reference.

expert reply by: Rachael H

0

Answer 1

Yes it will; a golf cart is absolutely compatible for use with the Erickson tie-down kit you asked about, which is the following part number: - Erickson ATV E-Track Tie-Down Kit w/ Ratchet Straps and Wheel Chocks #EM09160 You just need to ensure…

view full answer...

Answer 2

The safest way to secure a 4-wheeled vehicle like a golf cart in a truck bed is to use wheel nets that secure to the truck bed in some manner. The Erickson E-Track Tie-Down Kit #EM09160 is one option that is similar to the Pack 'Em kit you…

view full answer...

Answer 3

The Erickson Vertical E-Track - Zinc Coated Steel #E19146 referenced in your question is 4 inches long x 3-1/2 inches wide x 1/2 inches tall. The diameter of the mounting holes are 1/4 inches and the mounting hole spacing is 2 inches. I have…

view full answer...

Answer 4

The Erickson Horizontal E-Track, part #E19148 has 1/4 inch diameter mounting holes spaced 2 inches apart. The screws you use should be at least long enough to go 3/4 inch into the wood you are mounting the track to. The more screws you use the more…

view full answer...

Answer 5

In order to achieve the full capacity of the ratchet straps and the track, the direction of the pull should be parallel to the direction that the e track is running. How much the capacity would be diminished by pulling 90 degrees to the side will…

view full answer...

Answer 6

I spoke with Erickson about the Erickson Horizontal E-Tracks like part #E19148 and they stated that in order to obtain the full weight capacity you would need to use every hole. If you do not need the full weight capacity then you would just need…

view full answer...

Answer 7

If your trailer has separate turn signals from the brake lights and you want them to remain that way, you will need to use a special converter. On the trailer side, behind the 7-Way, you will attach the Vehicle to Vehicle Taillight Converter,…

view full answer...

Answer 8

Yes, you can use Erickson Horizontal E-Track item #E19148 as front straps to hold down a car. These tracks have a 2,000 lbs maximum capacity per track. You will want to use the etrailer E-Track Backing Plates w/ Hardware item #e96RR for mounting.…

view full answer...

Answer 9

The E-Track has slots that have a length of 2.45-inches and a width of .58 inches. See attached diagram. I couldn't find any information on the ANCOR brand so you would need to compare what you have to those dimensions to know if the…

view full answer...

Answer 10

The main difference between the horizontal and vertical E-tracks is which way the slots on the bar run. The horizontal E-track cargo control like part #E19148 can be mounted horizontally on the wall or floor in an enclosed cargo or open trailer. It…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...