Does Erickson ATV E-Track Tie-Down Kit Work With Golf Cart

Question

Question:

Will product work on my golf cart with stock tires and wheels ? I load it crossways on my aluminum car trailer.

asked by: Carter

0

Expert Reply:

Yes it will; a golf cart is absolutely compatible for use with the Erickson tie-down kit you asked about, which is the following part number:

- Erickson ATV E-Track Tie-Down Kit w/ Ratchet Straps and Wheel Chocks # EM09160

You just need to ensure your tires are between 10" and 30" in diameter, which the vast majority of golf cart tires are going to be, but I do recommend double-checking just to be on the safe side.

expert reply by: Kyle S

0

Answer 1

To install the Erickson E-Track 5 foot section #E19148 on your trailer you can use rivets, screws, or weld it to the trailer. Since your trailer is aluminum, welding may not be an option since the E-Track is steel. I recommend using screws, or…

view full answer...

Answer 2

The Replacement Touchscreen Remote w/ Charger for Lippert Ground Control 3.0 Electric Leveling System part #LC358601 will work on both the aftermarket and OEM Lippert Ground Control 3.0 Electric Leveling Systems. Therefore, if you had this same…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The etrailer E-Track Roller Idler #e67HR is 3" from the top of the e-track to the bottom of the roller.

view full answer...

Does Erickson ATV E-Track Tie-Down Kit Work With Golf Cart

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching