Bracket Kit Needed to Install Thule Xsporter 421 in 2005 Toyota Tacoma

Question

Question:

Hello ,I have a Thule 421 Xsporter and I need the clamps kit to adapt so it can fit a Toyota Tacoma 2005, do you have it?

asked by: Humberto

0

Expert Reply:

The bracket kit needed to install your Thule Xsporter 421 in a 2005 Toyota Tacoma would be the part # THXK3. Thule has confirmed for us that this bracket kit still works on the older model versions of the Xsporter.

expert reply by: Jameson C

0

Answer 1

The Yakima OutPost HD Overland Truck Bed Rack for Nissan/Toyota Utility Tracks part #Y01152-5868 for the 2013 Toyota Tacoma with deck rail system is not adjustable. If you need an adjustable ladder rack option for the 2013 Toyota Tacoma with deck…

view full answer...

Answer 2

I do have a recommendation for you, however, Yakima does not make an adapter for the Yakima HullHound Kayak Saddles w/ Tie-Downs part Y04079 that will allow them to work with the Thule Xsporter Pro Adjustable Height Truck Bed Ladder Rack part…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 5

Hey Shannon, thanks for reaching out! Sounds like you're looking for the Thule Xsporter Pro #TH500XTB-THXK3 for your 2008 Toyota Tacoma with the Deck Rail System. This is adjustable up and down as well as along the Deck Rail System so you get the…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Tracks can absolutely be installed on the roof of your A.R.E. Truck Cap to provide a mounting system for a roof rack. For this I recommend the Yakima Tracks, which come in 42 inch #Y01126, 54 inch #Y01127, and 60 inch #Y01135 lengths. These tracks…

view full answer...

Answer 8

The Rhino-Rack Roof Rack for Factory Tracks #Y02-490B-NT is going to be your best bet for the tracks on the ARE topper for your 2012 Toyota Tacoma. The weight capacity is 220 lbs like you mentioned, but that's going to be the highest you'll…

view full answer...

Answer 9

Yakima's Skyline towers part #Y53TR can fit the tracks of the Retrax XR that you have with the landing pad 1 part #Y00221 but there isn't a way with the Baseline towers. Your Yakima Corebar or Jetstream bars will work with the Skyline towers…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 12

I went ahead and brought the issue to my contact at Thule, and he said to either use WD-40 to spray on the available threading and use a pair of pliers to grab onto the T-Bolt while you try to rotate the knob. This will allow you to have extra…

view full answer...