Diameter of JIF Marine Table Leg For Octagonal Boat Table # 315-DSI-KS

Question

Question:

What is the Diameter of the mounting pole. My pontoon already has two recessed floor table mounts I want to make sure that the table pole will fit my existing mounts.

asked by: Jose M

0

Expert Reply:

The outside diameter of the Table Leg # 315-DTX for the Octagonal Boat Table # 315-DSI-KS is 2" in diameter. The end of the leg does taper down to 1-7/8".

expert reply by: Bud M

0

Answer 1

I've gone ahead and pulled the Octogon Boat Table #315-DSI-KF from our inventory to measure for your specific question. There is a depth of 2-1/4 inches from the top of the cup holder to the very bottom. If you notice in the pictures, there is a…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 10

Generally speaking wheel mount only bike racks are preferred. Especially for people with carbon fiber bike frames since frame mounts aren't recommended at all with them otherwise damage could occur. For other frame designs people still prefer…

view full answer...

Answer 11

A junction box/7-way plug kit like Epicord #277-000141 or #HS381-9000 lets you convert the camper to match the 7-way RV blade type connector format. This avoids the extra connection points and potential trouble spots from using separate adapters.…

view full answer...

Answer 12

There is not a plug and play adapter for your Lance connector that we are aware of. Typically this is installed by the Lance dealer. A junction box/7-way plug kit like #HS381-9000 is an option you have to convert the camper to match the 7-way RV…

view full answer...

Diameter of JIF Marine Table Leg For Octagonal Boat Table # 315-DSI-KS

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching