How To Remove Door on the Everchill RV Refrigerator w/ Freezer - 10.7 Cu Ft - 12V - Stainless

Question

Question:

How do you remove the door? Due to placement in the RV, the door does not open enough to adjust the shelves. Thanks for your assistance.

asked by: Claude P

0

Expert Reply:

The Everchill RV Refrigerator w/ Freezer part # 324-000119 is reversible so you can remove the door and install the hinge on the opposite side or simply remove the door for cleaning. I don't have an exact write-up for this process but it would be no different than removing the door from the refrigerator in your home. You'll first locate the hinge and use the appropriate tool for said fasteners which attach the hinge to the body. The fastener heads are likely covered with plugs you'd have to first pry out.

expert reply by: Conner L

0

Answer 1

The Classic Accessories PolyPro III Deluxe Travel Trailer Cover part #052963732634 is a great fit for your trailer. It&#39;s designed for trailers that are between 20 and 22 feet like yours and has zippered access panels that will line up…

view full answer...

Answer 2

The Everchill RV Refrigerator w/ Freezer, #324-000119 that we carry comes with option of reversing the doors. Simply unbolt the hinges from the doors and flip them then reinstall on the opposite side of the door.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 8

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only…

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...