How To Install Tekonsha Primus IQ Trailer Brake Controller On 2018 Ford Transit T250

Question

Question:

will it work on a ford transit 2018 250

asked by: Louis C

0

Expert Reply:

The Tekonsha Primus IQ Trailer Brake Controller part # TK90160 is compatible with a 2018 Ford Transit T250, you'll just need the Curt T-Connector Vehicle Wiring Harness part # C56327 and 4 to 7-Way with 4-Way Adaoter part # ETBC7L.

expert reply by: Conner L

0

Answer 1

There is not a factory brake controller plug-in port on your 2018 Ford Transit T250 so in order to install your existing Tekonsha Primus Brake Controller you will need to hardwire it in using the Wiring Kit #5506. This kit will provide you with the…

view full answer...

Answer 2

We have just what you need to get this job taken care of. There are two wiring kits you will need, the Curt T-Connector #C56327 and the Universal Installation Kit #ETBC7. These two kits combined will include everything you need to install a 7-way…

view full answer...

Answer 3

The Curt #C51180 will work just fine with a vehicle that is equipped with an OEM or aftermarket brake controller. The Echo will not receive any output from the existing controller, as the Echo doesn't have a pin to receive any output from…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

Hey HPA, I would go with the Air Lift kit part #AL64VJ that fits your 2019 Toyota RAV4 based on what you described and your needs. This gives you adjustable support that you can tailor as needed so that you get the exact amount of support you need…

view full answer...

Answer 11

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 12

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...