Replacement Hub For Boat Trailer That Uses A Dexter Bearing Kit # K71-G02-41

Question

Question:

Need help find HUB for my boat trailer, The bearing kit I use is a Dexter K71-G02-41 81140 1 3/8x1 1/16 I cant find the hub on your site. Thank You!

asked by: Westley C

0

Expert Reply:

The Dexter bearing kit includes the Bearings # L44649 & # L68149 which is the most popular size bearings used on 3,500LB axles. The Idler Hub # AKIHUB-545-35-G-EZ-K and Hub/Drum # AKHD-545-35-G-EZ-K both use these same bearings. These are both galvanized for superior corrosion resistance for your boat trailer. They both have the 5 on 4-1/2" bolt pattern which is the most common size. If you have a different bolt pattern please let me know your pattern.

Both kits use a 1.719" inner diameter Grease Seal # 58846. I have seen some of the Dexter marine axles use a 1.687" inner diameter Grease Seal # 168255TB. You will want to verify your seal by measuring the spindle with a Digital Caliper # PTW80157 or checking for identification numbers on the seal.

expert reply by: Bud M

0

Answer 1

EZ Lube axles like the item #T3584F-EZ-8974 come from the factory with just a little bit of grease in the bearings. The first time you use the EZ Lube feature to fill the axle, it will take a lot of grease. You will probably use 3/4 to a full tube…

view full answer...

Answer 2

Yes, the Curt hitch part #C77ZV is a fit for the 2023 Toyota Crown Hybrid. I attached a link to the install instructions as well as a link to an installer finder in case you wanted to find someone near you to install the hitch.

view full answer...

Answer 3

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 4

We offer replacement brake shoes for 10 x 1-1/2- and 10 x 2-1/4-inch electric drum brakes but no longer for the 1-3/4-inch width you reference. Dexter part #bp04-065 you referenced is a set of replacement brake shoes for electric trailer brakes…

view full answer...

Answer 5

I was able to find the exact replacement amber (1A-S-20A) and red (1A-S-20R) lenses. I did a Google search on kaper2 (or Kaper II), and found replacement lenses. Their replacement lenses are shown as measuring 4 inches long, by 2 inches wide by 3/4…

view full answer...

Answer 6

I do have an option for you but we don't carry any braking assemblies that are 10" diameter x 1-3/4" wide. These are an oddball size and would be best replaced with something more modern so you can access replacement parts if needed.…

view full answer...

Answer 7

There is a suggested and common method for 6 function trailer wiring. You will have the following functions: Right Turn, Left Turn, Ground, Tail/marker, Brake, Battery. I have included a help article on trailer wiring that includes a diagram and…

view full answer...

Answer 8

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 9

The factory trailer brake controller port on your 2021 Chevrolet Tahoe is located underneath the dash just to the left of the steering wheel. It will be taped to another harness so it may take a bit of looking to find. Keep in mind that if your Tahoe…

view full answer...

Answer 10

If your 2022 Chevrolet Tahoe does not have the factory tow package then the plug may not be there. If this is the case you would need to hardwire in a brake controller. If your Tahoe does have the tow package then the plug will be under the dash. The…

view full answer...

Answer 11

I do have an option for you but we have not yet gotten out hands on a 2019 Chevrolet Blazer therefore, have not had the chance to look for the brake controller wiring port either. I checked with both Tekonsha and Curt and it looks like they have not…

view full answer...

Answer 12

The proper replacement inner assembly member for your UFP 34043 would be indeed be the the Dexter #DX99FR which is compatible with disc brakes. The replacement has an electric lock out and has a 7500K capacity and is intended to work with a 2 inch…

view full answer...

Replacement Hub For Boat Trailer That Uses A Dexter Bearing Kit # K71-G02-41

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching