What Is The Bolt Pattern Of Vesper Steel Trailer Wheel TA65VR?

Question

Question:

I want to know the bolt on these rims? This will be for a 1950 Willeys Jeep with stock wheels and tires. I m looking to put on radial tires and need a one piece welded rim that is good quality and durable. Thank You for your time. Shawn

asked by: Shawn V

0

Expert Reply:

The Vesper wheel # TA65VR you were looking at have an 8 on 5-1/2" bolt pattern. I'll say that these have a slim chance of working on a vehicle as trailer wheels like # TA65VR have zero offset where typical vehicle wheels have offset to allow the wheel and tire to clear the body/suspension.

I included a video of the # TA65VR for you to take a look at.

expert reply by: Samuel C

0

Answer 1

It sounds like you are looking for 2 sets of left/right side brakes for your 7k trailer. If that is the case, we unfortuantely do not carry the 23-181-00 because these are an older brake model that was discontinued from Dexter. However, the new…

view full answer...

Answer 2

The difference between the Dexter Electric Trailer Brake Kit - 12" - Left and Right Hand Assemblies - 7,000 lbs #23-180-181 and the #23-105-106 you mentioned are the strength of the brake magnets. The #23-180-181 was designed for 7000lb…

view full answer...

Answer 3

The difference between the two brake assemblies comes down to one being self adjusting and one that is manually adjusted. I recommend the self adjusting because you will never have to crawl under the trailer to adjust the brakes. This can be a…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 6

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 7

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Answer 11

The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...