How to Determine Correct Replacement Slipper Springs

Question

Question:

I need a 27 inch 3 leaf Slipper spring along with the hardware

asked by: Christopher C

0

Expert Reply:

In order to find the correct replacement slipper spring you will need the length, width, and the capacity. The leaf count does not indicate capacity and is not important when determining a replacement. This information would also make a difference in the mounting hardware.

For example, the 4-Leaf Slipper Spring w/ Open Eye End # e24SR is 27" long, 1-3/4" wide, and designed for 4,300 lb axles. Assuming a single axle, you could use the # APS3SE and # APUBR-1 (this is for a 2-3/8" diameter axle) to mount it.

The 5-Leaf Slipper Spring w/ Hook End # e67SR is 27" long, 2" wide, and designed for 6,000 lb axles. Assuming a single axle you would need the # APS4 along with the # APUBR-9 (3" diameter axle) instead to mount the springs.

If neither of these match what you're looking for, I would be happy to help you find a replacement if you send me the additional measurements and capacity.

expert reply by: Robin H

0

Answer 1

Thank you for the pictures and the explanation! The leaf spring that fits the spacing you have is the 5-Leaf Slipper Spring w/ Hook End for 6,000-lb Trailer Axles #e67SR. If you check out the attached photo the "B" dimension is 24-1/4"…

view full answer...

Answer 2

If you are looking for a Leaf Spring that is 27-3/4 inches long, the closest that we offer in length is 27 inches. If your springs are worn, it is possible they were originally 27 inches long and have flattened out over time. We have a Double-Eye…

view full answer...

Answer 3

The Titan Chain Sliding Lashing Winch for Flatbed Truck or Trailer - 6,000 lbs #TCLR912 will work with straps like the Titan Chain Strap for Truck and Trailer Winch - Flat Hook - 4" x 30' - 5,400 lbs - Blue #TCLR430-1-33. This strap is what…

view full answer...

Answer 4

I have attached for you below some common torque values needed for a trailer suspension system but a lot of these will vary by bolt size and other factors. U-Bolts: Varies by Size - 1/2" bolts: 45 ft/lbs - 70 ft/lbs, 9/16" bolts: 65 ft/lbs…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Trailer leaf springs come in many different lengths and some may have the same capacity but different measurements and/or number of leaves. This is due to different configurations of trailers, axle spacing, and tire size. Ideally you would use the…

view full answer...

Answer 7

The brake assemblies you have are 7k Dexter assemblies that are 12 inch by 2 inch in size. The part number #AKEBRK-7-SA will work as a great replacement set. This includes assemblies for both sides of your trailer that are self adjusting.

view full answer...

Answer 8

To determine the correct E-Z Lube grease cap you are going to need to measure the center of the hub where the grease cap is going to fit (please see accompanying photo). The measurement will need to be very precise, so you are going to want to use a…

view full answer...

Answer 9

To determine the correct wiring for your trailer you will need to use a circuit tester, item #PTW2993, and attach the wires from the connector by function only. The light wires should be as follows, red is the stop turn wire and the black is the…

view full answer...

Answer 10

If your trailer has separate turn signals from the brake lights and you want them to remain that way, you will need to use a special converter. On the trailer side, behind the 7-Way, you will attach the Vehicle to Vehicle Taillight Converter,…

view full answer...

Answer 11

If I understand you correct you have a trailer with separate turn signals and brake lights that aren't functioning properly because you 2013 Ford F-150's trailer wiring combines those signals on one circuit. If I'm wrong let me know. If…

view full answer...

Answer 12

In order to upgrade from a 6 on 5-1/2" bolt pattern to a 8 on 6-1/2" bolt pattern on a Dexter 6K Axle you'll need the Dexter Trailer Hub and Drum Assembly part #42866UC3-EZ. The Dexter 5,200 lb - 7,000 lb axles all have the same size…

view full answer...