7-Way Opening Cover Plate for Chevrolet and GMC Truck Beds With Curt In Bed Wiring Harness

Question

Question:

I got this Curt harness for my 2022 Silverado 2500. Is there a way to fit this 7-way to the hole in the bed without leaving a strange hole above the connector for water and debris to get into?

asked by: Taylor R

0

Expert Reply:

You will need the Curt 7-Way Opening Cover Plate # C29CR when installing the Curt 5th Wheel/Gooseneck Custom Wiring Harness # C56000 on your 2022 Chevrolet Silverado 2500. This cover plate will fit in the oval opening in your truck be and allow you to use your Curt 7-way without having an additional opening.

expert reply by: Bud M

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

The best replacement pin box for the Lippert 1621 on your Grand Design Reflection 303RLS is the Curt Flex Air. This pin boxes has an air spring and shock absorber which will reduce the back and forth chucking (stopping and taking off) and lower the…

view full answer...

Answer 10

The most likely cause of the "no signal" error you are receiving with the Furrion Vision S Wireless RV Backup Camera System part #FOS43TASF is due to an interruption on the camera's power wire. Make sure that the camera is receiving…

view full answer...

Answer 11

Yes. You will have to use the Demco Hijacker Autoslide Capture Plates for Trailair Rota-Flex Pin Boxes #DM6171 on your 2021 Grand Design Reflection 337RLS. As far as which Curt Flexair works for your trailer, it depends on what pinbox you currently…

view full answer...

Answer 12

The shortest gooseneck ball we have for the 2024 Chevy puck system is the Reese Elite Series Pop-In Ball #RP23FR. This is going to be very similar to the Curt ball you mentioned. I have included some dimensions of the Reese ball below. From the top…

view full answer...