Recommended A-Frame Trailer Jack That Can Be Installed With The Crank Handle Facing The Trailer

Question

Question:

Do you sell any 5000 lb jacks that have or can be installed where the turn handle faces towards the trailer or to the side instead of being out in front? Im trying to figure out a way where I can open the tailgate on my F-150 with the trailer attached, but the handle on our current one I think its a Lippert gets in the way. Thanks in advance!

asked by: Annie C

0

Expert Reply:

Yes, you can just install the Trailer Valet JXC Trailer Jack w/ Footplate # TV94FR with the handle facing your trailer. The round mounting bracket has multiple holes to give you multiple points to secure it to the tongue of the trailer. That being said, you may have to drill new holes in the tongue if none of the holes line up.

expert reply by: Kevin C

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 5

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

I spoke to Dexter and they said there is a bit of a process for installing the spindle nut properly. 1. You will need to thread on the inner nut, rotate the hub, then tighten the nut to 100 foot pounds. 2. Loosen the nut to remove the torque, making…

view full answer...

Answer 8

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 9

Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.

view full answer...

Answer 10

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 11

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...