Recommended 3/8" - 1/2" Truck Bed And Tailgate Mat For A 2022 GMC Sierra 2500

Question

Question:

Do you have something like this available?

asked by: Scott

0

Expert Reply:

We carry the Black Armour Heavy-Duty Custom Truck Bed Mat # BA34AR, which will cover your 2022 GMC Sierra 2500's bed and is the thickest option at 1/2" thick. For the tailgate we carry the DeeZee Universal Truck Tailgate Mat # DZ86700, which is 3/8" thick.

If you wanted a matching design then you could use the # DZ86700 along with the Dee Zee Custom-Fit Truck Bed Mat # DZ87021, but this bed mat is only 3/8" thick.

expert reply by: Kevin C

0

Answer 1

I can tell you how to easily determine the correct over/under conversion kit for your 2017 K-Z Sportsmen Classic 180THT, though we would not be able to verify a specific fit for any trailer. It's easy to determine the correct over/under lift kit…

view full answer...

Answer 2

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 3

Yes, you can use the over/under conversion kit #K71-385-00 to move the axles to the tops of the leaf spring stacks. Dexter has the following note on the conversion kits: When converting from underslung to overslung, the installation of bump stops to…

view full answer...

Answer 4

You really need to have a minimum of 6 inches between the bed rails of a truck and the overhang of the fifth wheel/gooseneck trailer. Some say that 4 inches is adequate but if you are in a hilly area at all you'll want the 6 inches. Typically on…

view full answer...

Answer 5

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 6

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

Answer 7

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

Answer 8

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 9

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 10

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 11

Since the issue appears to be on the vehicle side for your 2017 Toyota Tacoma, I recommend first checking the connector itself. Look to see if there is any dirt or corrosion built up inside the connector that may preventing a solid connection with…

view full answer...

Answer 12

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...