Replacement Red and Amber Lenses for MC44 Series and BA44 Series Trailer Lights

Question

Question:

Just lenses for mcl44ab1 and mcl44rbi

asked by: Jim E

0

Expert Reply:

For just the replacement lens for the Optronics LED Trailer Clearance or Side Marker Light Red Lens item # MCL44RB1 you will want the Replacement Red Lens for MC44 Series and BA44 Series Trailer Lights item # A44RB.

For just the replacement lens for the Optronics LED Trailer Clearance and Side Marker Light item # MCL44AB1 you will want the Replacement Amber Lens for MC44 Series and BA44 Series Trailer Lights item # A44AB.

expert reply by: Jerred H

0

Answer 1

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 2

Finding continuity to ground on the running light circuit of your trailer indicates that the circuit has a short to the frame of the trailer most likely and is your problem. What you'll need to do is trace the circuit starting at the assemblies…

view full answer...

Answer 3

I'm not sure why they said those were your only options, but we do have the correct replacement oil seal for your Dexter 10k hub from 2006, and is the exact replacement for a National 370150BG: - Unitized Oil Seal #10-51 The #10-51 has an inner…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...