Does The Air Lift LoadLifter 7500 XL Have An Internal Jounce Bumper?

Question

Question:

Please check this and confirm which one is it: have or not the jounce? Thank you.

asked by: Jose M

1

Helpful Expert Reply:

Yes, the Replacement Air Spring for Air Lift LoadLifter 7500 XL System # AL50236 does have an internal jounce bumper.

This air spring is a replacement hybrid spring for your Air Lift LoadLifter 7500 XL Air Helper Spring System, and is made in the USA.

I have also included a product overview video for you to check out as well.

expert reply by: Bryce D

1

Answer 1

I reached out to my contact at AirLift and they were able to tell me that the mounting diameter of the Replacement Air Spring for AirLift 7500XL #AL50236 is 8" wide- so you will need at least 8" of lateral clearance in order to…

view full answer...

Answer 2

Yes, the Replacement Air Spring for Air Lift #AL50236 for the Air Lift LoadLifter 7500 XL #AL57538, does have an internal jounce. If you want 6" air springs, you'll want the Air Lift LoadLifter 5000 Air Helper Springs #AL57385.…

view full answer...

Answer 3

I have a solution for you, but the differences between the AirLift 5000 #AL89295 and AirLift 7500 #AL57595 extend to the brackets and mounting hardware. For that reason you won't just be able to swap out your 5000 air bags with the…

view full answer...

Answer 4

The Air Lift Air Spring #AL50236 has what they call a design height of 7". There are 3 different height bags (5.5", 6" and 7") and they are determined by the number stamped on the side of the bag. The bags that…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to calculate where the axles would go on your trailer, there are several things that need to be taken into consideration. You will have to mock up the trailer with the suspension and axles to get the weights needed to determine where the…

view full answer...

Answer 11

Equalizers for trailer suspension have different shapes, lengths, and heights to accommodate different axle spacing, spring lengths, and deck heights. Going to an equalizer that is not the same length and height as the original will require replacing…

view full answer...

Answer 12

In the image with the suspension setup the equalizer #TREQ105 is placed between the front and second axles. Just like you have on your trailer. The front of the equalizer connects to the spring using a shackle strap and the rear is connected directly…

view full answer...