Can The Rampage Clinometer With Compass Be Installed In Any Orientation?

Question

Question:

Can it be mounted on the ceiling or upside down?

asked by: Ray B

1

Helpful Expert Reply:

The Rampage Clinometer with Compass # RA791006 must be installed right side up, and can not be installed on the ceiling or upside down.

You're going to want to make sure you're on even, level ground when you go to install it for the most accurate readings.

expert reply by: Bryce D

1

Answer 1

The Rampage Clinometer with Compass - Analog #RA791006 will help you detect if you are on level ground or not with your RV, so it will absolutely be a help. It will only detect how level the ground is under your tires and suspension, so there may…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 6

Hey Jason, I spoke with Furrion and they stated that the Furrion Chill Cube is OEM only currently and should be released to the aftermarket distributors later on this year (2024), but there is no solid date. That says to me that they're probably…

view full answer...

Answer 7

Since the bolt holes line up vertically and horizontally you'll be able to bolt the Trailair Air Ride 5th Wheel King Pin - Leland 7920 #UF35-946208. This specific pin box actually has an 18" king pin to first set of bolt holes measurement…

view full answer...

Answer 8

I took a look at the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 that you mentioned and it's actually going to be a fit for the Lippert 1621 and 1621 HD 5th-wheel pin boxes, and not your Leand 7920, however I do have another…

view full answer...

Answer 9

The mounting holes of the Swing Out Extension Brackets part #LC182496 that you referenced are for the side that attaches to the jack itself and not the portion that attaches to the camper. You'd need to attach these to the L-bracket on the camper…

view full answer...

Answer 10

The Swing Out Extension Brackets for HappiJac Truck Camper Jacks - Qty 2 #LC182496 will have 3.5 inches up to 4.5 inches depending on your camper brackets. This will be per side. Based on your photos it looks like you'll get about 3.5 inches per…

view full answer...

Answer 11

You are correct that the difference between using the standard mounting option on the HappiJac Electric Truck Camper Jack System #LC736515-ELKIT and adding the Swing Out Extension Brackets for HappiJac Truck Camper Jack Systems #LC182496 is that the…

view full answer...

Answer 12

Yes the Happijac swing out bracket kit part #LC182496 does work with your camper with a set of Happjac truck camper jacks and would also work/be needed for your 2021 Ram truck that is a dually.

view full answer...