What is the Hitch Pin Hole Size for Curt Class IV Trailer Hitch # C14081

Question

Question:

I was wondering since this is a class iv hitch does it use a standard pin for the hitch. Just wondering if i can use my current ballmounts from my class 3 with this hitch?

asked by: Austin

0

Expert Reply:

Curt Class IV trailer hitch # C14081 takes a 5/8 inch diameter pin the same as a Class III hitch. The outer width of the receiver is the same as well so the pin or lock does not have to be any longer. You can use your existing ball mounts that you were previously using with a Class III hitch. No worries!

expert reply by: Michael H

0

Answer 1

A Class IV hitch such as #C14081 might actually have a higher capacity than your 1997 GMC C/K series truck (check the owner's manual) so provided that the trailers you will be towing now and in the future are within the capacities of the truck…

view full answer...

Answer 2

The Curt Class IV, part #C14081 would work great for you. According to Curt, the spare will need to be dropped temporarily in order to facilitate the installation, but once the hitch is in place, the spare will fit back in its original location. This…

view full answer...

Answer 3

Yes, the Curt trailer hitch part #C14081 that you referenced is a confirmed fit for your 1990 Chevy C1500 Stepside. We actually had a customer come back with the GMC version of your truck and leave us a review saying that this hitch worked well for…

view full answer...

Answer 4

I'd recommend the Curt Class IV hitch, part #C14081. When installed, the hitch will sit pretty tightly to the underside of the rear bumper, as would the Draw-Tite #41901 you looked at, but the Draw-Tite model only fits the long bed model truck.…

view full answer...

Answer 5

I checked out the installation instructions for both of the trailer hitches you referenced for your 1998 Chevrolet CK pickup truck. Both of the hitch instructions do mention the spare tire. For the Draw-Tite Trailer Hitch, part #41938 the…

view full answer...

Answer 6

The hitches that are listed for the 1998 GMC trucks with 34 inch frames are the ones that are designed to fit the cab and chassis models. The #C14081 that you referenced would work well on your truck with a 37 inch frame since it is not a cab and…

view full answer...

Answer 7

As we have not had a 1973 Ford F-100 in our shop to test fit the available receivers I can only give you the measurements from one of our receivers so that you can see where it will sit on your truck. The Curt Trailer Hitch Receiver #C14082 is…

view full answer...

Answer 8

I went out to the warehouse to take some measurements of Curt trailer hitch #C14082. I made a picture showing the measurements for you. The bolt holes, starting from the one furthest forward on the vehicle, measures 2-3/4 inches to the center of the…

view full answer...

Answer 9

The distance from the crosstube to the very end of the receiver is 8 inches for the Curt Trailer Hitch Receiver #C14082.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

What is the Hitch Pin Hole Size for Curt Class IV Trailer Hitch # C14081

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching