Trailer Hitch for 1976 Chevy C/K Series Stepside With Short Bed

Question

Question:

HI, I have a 1976 Chevy k10 short bed stepside. I need a hitch that does not interfere with the spare tire mounted under the truck. Thanks

asked by: Rosemary

0

Expert Reply:

The trailer hitch that fits your 1976 Chevy K10 short bed stepside, and will not interfere with your spare tire is the Curt Trailer Hitch Receiver # 13028. You will need to remove the spare tire initially when you are installing the hitch, but you will put it back on after the hitch is in place. I have added a link to the instructions for you which detail this.

expert reply by: Kyle S

0

Answer 1

I love that body style! The Curt #13028 is a fit if the truck is equipped with the standard factory style or step bumper.

view full answer...

Answer 2

Sounds like your 1987 Chevy truck has the standard bumper which we have plenty of hitches for. The Curt hitch part #13028 is the most popular option we carry. When this is installed you will basically just see the hitch opening below the bumper. I…

view full answer...

Answer 3

For your 1986 Chevrolet C/K Series pickup with 6-foot bed and step bumper we have no B&W hitch fits confirmed. Hitch #BWHDRH25198 fits only the version of your truck that has the deep drop bumper. The hitch options that do fit your truck are…

view full answer...

Answer 4

This will fit your 1985 Chevrolet C/K Series Pickup as long a you have an 8 foot bed and a deep drop bumper. You will have to drill six 7/32 inch holes in order to install this Curt Trailer Hitch, part #C13099, but you will not need to do any…

view full answer...

Answer 5

From side to side, the mounting holes measure 31-1/4 inches apart, center to center. All three sets of holes are the same distance apart. From rear to front, beginning at the rear of the vehicle the distance from the first set of holes to the second…

view full answer...

Answer 6

The distance from the crosstube to the very end of the receiver is 8 inches for the Curt Trailer Hitch Receiver #C14082.

view full answer...

Answer 7

The Curt Trailer Hitch Receiver part #13028 is designed to fit the following vechiles: - 88-91 CHEVY/GMC 4 DR CREW CAB ONLY - 73-79 FORD 250 CREW CAB - 73-06 CHEVY/GMC FULL SIZE CAB & CHASSIS w 34" FRAME - 73-06 FORD PICKUP: CAB AND CHASSIS…

view full answer...

Answer 8

The 1974 Chevrolet C10 is categorized as a C/K Series not a C-Series which I think may be where the problem lies. I recommend the Curt Trailer Hitch Receiver part #13028 which is a confirmed fit for a Chevrolet C10 from 1963-1987. The Draw-Tite…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Trailer Hitch for 1976 Chevy C/K Series Stepside With Short Bed

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching