Replacement Pitch Arm Assembly for Solera XL 63 Flat Arm Support

Question

Question:

Is there a difference between the white - LC62NJ - and the black - LC67VR? I have black but it is out of stock. Can I order the white?

asked by: Jon L

0

Expert Reply:

The only difference between the Replacement Pitch Arm Assembly white item # LC62NJ and the black item # LC67VR is the color. Both replace the pitch arm assembly needed for your Solera XL 63" long flat awning support arm.

expert reply by: Jerred H

0

Answer 1

You will want to measure the length of your current Solera awning pitch arms and match up the correct size on the link I attached for you. Based on the photo you attached, you will likely need one of the following sizes: -Replacement Pitch Arm…

view full answer...

Answer 2

There isn't an available replacement bolt and nut from Lippert for the Replacement Pitch Arm Assembly for Solera 69" Standard Flat Awning Support Arm - Black #LC375994, so a new arm would be required if yours is damaged. There is a…

view full answer...

Answer 3

It sounds like you're needing the Replacement Pitch Arm Assembly for Solera XL 63" Flat Awning Support Arm which comes in Black #LC67VR or White #LC62NJ depending on your application. These have an overall length of 33".…

view full answer...

Answer 4

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 5

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 6

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 7

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 8

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 9

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 10

Most of the time when a tow setup is porpoising with a weight distribution system all you have to do is add a bit more spring bar tension to minimize the porpoising. With an Equalizer system you would need to angle the spring bars down further to add…

view full answer...

Answer 11

The Blue Ox systems cannot be moved back that far but we do have the perfect system for you. Take a look at the Reese SC weight distribution systems linked to the right (minus the ones that say Light Duty). These systems have narrow brackets that can…

view full answer...

Answer 12

You can get a new brake mounting flange for your axle. The old flange will need to be cut off. The part is #4-44-1. This is designed to fit a 3 inch trailer axle and should be welded in place by a professional. Since you would also have to get the…

view full answer...