Bolt Hole Dimension of the Pollak Replacement 7-Way # PK11893

Question

Question:

Could you please tell me what the measurements are for the bolts? From the top bolt to the bottom bolt and from side to side. Thank you

asked by: Autumn

0

Expert Reply:

If you check out the picture I attached you will see the dimensions of the bolt holes of the Pollak Replacement 7-Way # PK11893 that you referenced.

The vertical holes are 1-3/4 inches apart measured on center and the horizontal holes are 2-1/2 inches apart measured on center.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I attached a picture that shows the pin out diagram for the Pollak 5th Wheel / Gooseneck T-Connector with 7-Pole #PK11893-11932 that you referenced.

view full answer...

Answer 2

I recommend using the Pollack Replacement 7-Way Trailer Connector Socket, #PK11893, and the 4ft Pigtail Wiring Harness, #PK11998. The screw holes for the 7-way socket are 2-1/2 inches x 1-3/4 inches, which match your specification. I have attached a…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 10

Hey Eric, the Curt Multi-Fit Ball Kit w/ 4" Offset for Chevy/Ford/GMC/Nissan Underbed Gooseneck Hitch #C68ZV is not going to work with your Ram, unfortunately. This one is only going to work for select YMM (Year Make Model) Ford 250-450s, GMC…

view full answer...

Answer 11

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 12

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Bolt Hole Dimension of the Pollak Replacement 7-Way # PK11893

Product Page this Question was Asked From

Continue Researching