Lift Kit that Fits Dexter Torflex 2,200 lb Trailer Axle

Question

Question:

It looks correct for my trailer but I wanted to confirm that this lift kit is the correct one. See pictures I attached for axle PN.

asked by: Scott B

1

Helpful Expert Reply:

Since we know that the Dexter Torflex 2,200 lb axles are the number 10 Torflex axles the correct tandem axle lift kit you'd need is the # K71-707-02 that you referenced so this would be the kit you need.

expert reply by: Jameson C

1

Dexter 2,200 Torflex Axle Sticker
(click to enlarge)

Answer 1

To raise your 2014 Rockwood Mini Lite 2109S Ultralite Travel Trailer, with Dexter 2200 axles, you will want to use the Correct Track Trailer Alignment and Lift Kit - Tandem Axle item #RR23QX. This kit will raise your trailer height by 1-1/4"…

view full answer...

Answer 2

I have a lift kit option for you, but there is not a shock kit currently made for torsion axles. For the #10 toflex axle in your 2017 Casita 17 we have the Torflex Lift Kit - Single Axle - 2-5/8" Lift #K71-707-01 if you have tandem axles…

view full answer...

Answer 3

It's ok if you have 2,200 lb axles; so long as you have a #10 Dexter Torflex Axle the correct lift kit is the following: - Torflex Lift Kit - Tandem Axle #K71-707-02

view full answer...

Answer 4

It appears that the 2003 Jayco Kiwi 21C would have came with a #10 Dexter torsion axle. You can verify this if you still have an axle tag on one of your 2 axles or by measuring the bolt hole spread where the axle mounts to the frame. This should be…

view full answer...

Answer 5

I spoke to my contact at Dexter Axle and they confirmed that you have a #11 Torflex Axle on your 2021 Airstream Caravell 22FB. The correct lift kit for that axle is the Torflex Lift Kit - Tandem Axle - 2-7/8" Lift #K71-724-02. This…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 8

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 9

While we have the measurements of the exact ground clearance height for our hitches we carry for a 2022 Toyota Sienna, we do have available measurements for a 2021 model. While these are not exact, the measurements will not deviate much from the…

view full answer...

Answer 10

The 18.5x8.5-8 is actually an old tire size that is not used much anymore. The closest metric size to your existing tire would be 215/60-8. Your wheel most likely has a 5-on 4-1/4 inch bolt pattern (see link), you will want to make sure that the bolt…

view full answer...

Answer 11

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 12

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Lift Kit that Fits Dexter Torflex 2,200 lb Trailer Axle

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching